Ao100config
- Copy this into a text file, save as a .ini
- generated by Slic3r 0.9.9-dev on Sat Feb 23 23:30:57 2013
avoid_crossing_perimeters = 0 bed_size = 140,200 bed_temperature = 70 bottom_solid_layers = 3 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = 0 cooling = 1 default_acceleration = 0 disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 T0 S0 ; turn off temperature\nM104 T1 S0 ; turn off temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ; move bed to the front\nG28 X0 ; home X axis\nM84 ; disable motors external_perimeter_speed = 100% extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0 fan_always_on = 1 fan_below_layer_time = 60 filament_diameter = 2.95 fill_angle = 45 fill_density = 0.3 fill_pattern = line first_layer_bed_temperature = 75 first_layer_extrusion_width = 200% first_layer_height = 0.35 first_layer_speed = 30% first_layer_temperature = 185 g0 = 0 gap_fill_speed = 0 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_only_where_needed = 0 infill_speed = 80 layer_gcode = layer_height = 0.3 max_fan_speed = 80 min_fan_speed = 30 min_print_speed = 10 min_skirt_length = 0 notes = nozzle_diameter = 0.5 only_retract_when_crossing_perimeters = 1 output_filename_format = [input_filename_base].gcode perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 2 post_process = print_center = 70,100 raft_layers = 0 randomize_start = 1 retract_before_travel = 2 retract_length = 1 retract_length_toolchange = 25 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 25 rotate = 0 scale = 1 skirt_distance = 6 skirt_height = 2 skirts = 2 slowdown_below_layer_time = 15 small_perimeter_speed = 45 solid_fill_pattern = rectilinear solid_infill_below_area = 30 solid_infill_every_layers = 0 solid_infill_speed = 80 start_gcode = G28 ; home all axes\nM140 S70 support_material = 0 support_material_angle = 0 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_layers = 0 support_material_interface_spacing = 0 support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 45 temperature = 180 threads = 1 toolchange_gcode = top_solid_infill_speed = 50 top_solid_layers = 3 travel_speed = 80 use_relative_e_distances = 0 vibration_limit = 0 z_offset = 0