Difference between revisions of "Boss Laser Settings"
Jump to navigation
Jump to search
m (add link to boss) |
|||
(8 intermediate revisions by 3 users not shown) | |||
Line 14: | Line 14: | ||
! Speed (mm/second) | ! Speed (mm/second) | ||
! Power (%) | ! Power (%) | ||
+ | ! Kerf | ||
+ | |- | ||
+ | | Acrylic | ||
+ | | 1/16" | ||
+ | | 50 | ||
+ | | 50 | ||
+ | | | ||
|- | |- | ||
| Plywood | | Plywood | ||
Line 19: | Line 26: | ||
| 25? | | 25? | ||
| 80 | | 80 | ||
+ | | | ||
+ | |- | ||
+ | | MDF Core Plywood (Owl Lumber) | ||
+ | | 0.177" | ||
+ | | 25 | ||
+ | | 75 | ||
+ | | 0.0184 | ||
|- | |- | ||
| ABS | | ABS | ||
Line 24: | Line 38: | ||
| 20 | | 20 | ||
| 65 | | 65 | ||
+ | | | ||
+ | |- | ||
+ | | Balsa | ||
+ | | 1/16" medium density | ||
+ | | 150 | ||
+ | | 10 | ||
+ | | | ||
+ | |- | ||
+ | | Balsa | ||
+ | | 3/32" medium density | ||
+ | | 150 | ||
+ | | 25 | ||
+ | | | ||
+ | |- | ||
+ | | Balsa | ||
+ | | 1/8" medium density | ||
+ | | 150 | ||
+ | | 30 | ||
+ | | | ||
|- | |- | ||
| Cermark Engraving Brass | | Cermark Engraving Brass | ||
Line 29: | Line 62: | ||
| 30 | | 30 | ||
| 70 | | 70 | ||
+ | | | ||
|- | |- | ||
| Masonite | | Masonite | ||
Line 34: | Line 68: | ||
| 15 | | 15 | ||
| 50 | | 50 | ||
+ | | 0.5mm | ||
+ | |- | ||
+ | | MDF | ||
+ | | 1/4" | ||
+ | | 7.5 | ||
+ | | 70 | ||
+ | | 0.6mm | ||
+ | |- | ||
+ | | Mylar sheet | ||
+ | | 7.5mil (190 micron) | ||
+ | | 30 to 150 | ||
+ | | 10 | ||
+ | | | ||
|} | |} | ||
Line 63: | Line 110: | ||
| 100 | | 100 | ||
| 25 | | 25 | ||
+ | |- | ||
+ | | Speedycarve (rubber) | ||
+ | | ~1mm | ||
+ | | 50 | ||
+ | | 10 | ||
|} | |} |
Revision as of 15:19, 26 January 2019
The below is to help you figure out your settings for your cutting job on the Boss Laser. Please do not be creative with settings unless you know what you're doing, because you can easily set things on fire.
Test Cuts
There are several test cut pieces. These test various power/speed in a pie shape going from 10% to 100%. These are a good starting point.
Known Settings
Known, successfully used settings.
Cutting
Material | Thickness | Speed (mm/second) | Power (%) | Kerf |
---|---|---|---|---|
Acrylic | 1/16" | 50 | 50 | |
Plywood | 1/4" | 25? | 80 | |
MDF Core Plywood (Owl Lumber) | 0.177" | 25 | 75 | 0.0184 |
ABS | 1/8" | 20 | 65 | |
Balsa | 1/16" medium density | 150 | 10 | |
Balsa | 3/32" medium density | 150 | 25 | |
Balsa | 1/8" medium density | 150 | 30 | |
Cermark Engraving Brass | 30 | 70 | ||
Masonite | 1/8" | 15 | 50 | 0.5mm |
MDF | 1/4" | 7.5 | 70 | 0.6mm |
Mylar sheet | 7.5mil (190 micron) | 30 to 150 | 10 |
Engraving
Material | Depth | Speed (mm/second) | Power (%) |
---|---|---|---|
Masonite | 0.4mm | 100 | 10 |
Masonite | 1mm | 100 | 15 |
Masonite | 1.3mm | 100 | 20 |
Masonite | 1.6mm | 100 | 25 |
Speedycarve (rubber) | ~1mm | 50 | 10 |