Difference between revisions of "Evenheat 810 Kiln"

From Pumping Station: One Wiki
Jump to: navigation, search
m (add major components gallery)
m (add usage information)
Line 1: Line 1:
 +
The Evenheat 810 Kiln has two primary parts: the kiln itself and a temperature controller, which senses the temperature inside the kiln using a thermocouple and interrupts the power supplied to the kiln when it reaches the desired temperature.
 +
 
{{Template:EquipmentPage
 
{{Template:EquipmentPage
 
|owner=PS:One
 
|owner=PS:One
Line 17: Line 19:
 
<gallery>
 
<gallery>
 
File:Evenheat-810-temperature-controller-plug.jpg|The temperature controller's power plug.
 
File:Evenheat-810-temperature-controller-plug.jpg|The temperature controller's power plug.
File:Evenheat-810-power-controller.jpg|The temperature controller's power switch; the kiln's power plug is plugged into the outlets, to the left of the switch, and should not be unplugged.
+
File:Evenheat-810-power-controller.jpg|The temperature controller's power switch; the kiln's power plug is plugged into the temperature controller output outlets, to the left of the switch, and should not be unplugged.
File:Evenheat-810-temperature-control-panel.jpg|The temperature controller's control panel; the current temperature will display in the top readout, in red, while the target temperature will display in the bottom readout, in green; the up & down chevron buttons below the display change the target temperature.
+
File:Evenheat-810-temperature-control-panel.jpg|The temperature controller's control panel; the current temperature will display in the top readout, in red, while the target temperature will display in the bottom readout, in green; the up & down chevron buttons below the display change the target temperature. Note: both the desired & current temperatures read out in Fahrenheit.
 
File:Evenheat-810-thermocouple-port.jpg|The kiln's thermocouple port, with the thermocouple inserted.
 
File:Evenheat-810-thermocouple-port.jpg|The kiln's thermocouple port, with the thermocouple inserted.
 
File:Evenheat-810-thermocouple-tip.jpg|The tip of the kiln's thermocouple, on the other side of the port.
 
File:Evenheat-810-thermocouple-tip.jpg|The tip of the kiln's thermocouple, on the other side of the port.
Line 25: Line 27:
 
File:Evenheat-810-main-cutoff-on.jpg|The kiln's main power cutoff, in the 'on' position; note how the button is pushed in, and the lever is pulled slightly upward.
 
File:Evenheat-810-main-cutoff-on.jpg|The kiln's main power cutoff, in the 'on' position; note how the button is pushed in, and the lever is pulled slightly upward.
 
</gallery>
 
</gallery>
 +
 +
== Usage ==
 +
 +
=== Firing the kiln ===
 +
 +
# Plug in the temperature controller's power plug and flip the controller's power switch; this will light up the temperature controller's control panel. The current temperature (in red) should read room temperature (somewhere around 70F). Touch the thermocouple tip for a minute and check that the current temperature raises closer to the mid/high 80s (the temperature of the surface of your skin), to ensure that the thermocouple's polarity is correct.
 +
# If the thermocouple is not inserted through the kiln's thermocouple port, insert it. Place the pieces to be heated in the kiln.
 +
# Make sure the kiln's power plug is plugged into the temperature controller's outlets. Switch the two switches on the kiln's main controller to the 'on' position (to the left).
 +
# When you are ready to actually start heating the kiln, press in the kiln's main power cutoff button while lifting the cutoff lever away from the kiln controller's face. The button should lock in the inward ('on') position. Allow the cutoff lever to lower down to its resting position; it should sit at an angle from the face. If the kiln has been powered on correctly, the light directly below the upper switch on the kiln's controller face will glow orange. The power cutoff button can be returned to the outward ('off') position, killing power to the kiln, by pressing the lever down against the face of the kiln controller.
 +
 +
=== Finishing a firing ===
 +
 +
# Kill the power to the kiln by pressing the main cutoff lever against the controller face, returning the main cuttoff button to the outward ('off') position. The indicator light on the main controller face should shut off.
 +
# Shut off the two power switches on the main kiln controller face, as well as the temperature controller power switch, next to its power output outlets. When this is done, the kiln should be entirely cut off from electricity.
 +
# Open the kiln and remove the contents. Wear proper PPE.
 +
# Leave the kiln lid open, to let its interior cool. The kiln is heavily insulated, so it will take a very long time to cool if the lid is left closed; that may be a desired temperature profile.
  
 
== History ==
 
== History ==

Revision as of 20:38, 29 January 2019

The Evenheat 810 Kiln has two primary parts: the kiln itself and a temperature controller, which senses the temperature inside the kiln using a thermocouple and interrupts the power supplied to the kiln when it reaches the desired temperature.


Evenheat 810 Kiln
Evenheat-810-kiln.jpg
Owner/Loaner PS:One
Serial Number 38008
Make/Model Evenheat 810
Arrival Date 2010
Usability Yes
Contact {{{contact}}}
Where Small Metals
Authorization Needed yes
Hackable no
Estimated Value $865
Host Area Small Metals


Evenheat 810 Kiln Area: Small Metals https://wiki.pumpingstationone.org/Evenheat_810_Kiln



Major Components

Usage

Firing the kiln

  1. Plug in the temperature controller's power plug and flip the controller's power switch; this will light up the temperature controller's control panel. The current temperature (in red) should read room temperature (somewhere around 70F). Touch the thermocouple tip for a minute and check that the current temperature raises closer to the mid/high 80s (the temperature of the surface of your skin), to ensure that the thermocouple's polarity is correct.
  2. If the thermocouple is not inserted through the kiln's thermocouple port, insert it. Place the pieces to be heated in the kiln.
  3. Make sure the kiln's power plug is plugged into the temperature controller's outlets. Switch the two switches on the kiln's main controller to the 'on' position (to the left).
  4. When you are ready to actually start heating the kiln, press in the kiln's main power cutoff button while lifting the cutoff lever away from the kiln controller's face. The button should lock in the inward ('on') position. Allow the cutoff lever to lower down to its resting position; it should sit at an angle from the face. If the kiln has been powered on correctly, the light directly below the upper switch on the kiln's controller face will glow orange. The power cutoff button can be returned to the outward ('off') position, killing power to the kiln, by pressing the lever down against the face of the kiln controller.

Finishing a firing

  1. Kill the power to the kiln by pressing the main cutoff lever against the controller face, returning the main cuttoff button to the outward ('off') position. The indicator light on the main controller face should shut off.
  2. Shut off the two power switches on the main kiln controller face, as well as the temperature controller power switch, next to its power output outlets. When this is done, the kiln should be entirely cut off from electricity.
  3. Open the kiln and remove the contents. Wear proper PPE.
  4. Leave the kiln lid open, to let its interior cool. The kiln is heavily insulated, so it will take a very long time to cool if the lid is left closed; that may be a desired temperature profile.

History

On 1/28/2013 this was tested to at least power up and create heat.
3/3/2014. Inspect and test all mechanical and electrical components.
Remove upper switch, disassemble, clean contacts, reassemble and reinstall.
All components appear to works as intended.

Heating Profile

On 3/3/2014 I ran the kiln using a PID temperature controller set to 2200f.
Room temp to 500f. 7 min.
Room temp to 1000f. 17 min.
Room temp to 1500f. 40 min.
Room temp to 2000f. 95 min.

Important Documents