Difference between revisions of "Jet Wood Lathe"
Jump to navigation
Jump to search
(Clarified some rules, formatting) |
(How to get certified, danger committee, link to checklist) |
||
Line 53: | Line 53: | ||
* Check your workpiece for flaws, cracks, knots etc. and test glue joints before mounting the workpiece on machine. | * Check your workpiece for flaws, cracks, knots etc. and test glue joints before mounting the workpiece on machine. | ||
* Use the lowest speed when starting a new workpiece. | * Use the lowest speed when starting a new workpiece. | ||
− | |||
== Don't == | == Don't == | ||
Line 60: | Line 59: | ||
* Touch your project by hand while the lathe is running | * Touch your project by hand while the lathe is running | ||
+ | ==How To Get Certified== | ||
+ | The area host has determined that certifications for this machine should not be viral. | ||
+ | |||
+ | A list of members allowed to certify others will be posted here when the Danger Committee has finish creating a process. | ||
== List of Currently Certified Users == | == List of Currently Certified Users == | ||
Line 66: | Line 69: | ||
! Trained By | ! Trained By | ||
|- | |- | ||
+ | |Matt Triano | ||
+ | |Danger Committee | ||
+ | |- | ||
+ | |Joeseph Nudell | ||
+ | |Danger Committee/Owner | ||
+ | |- | ||
+ | |Jason Shanfield | ||
+ | |Danger Committee | ||
+ | |- | ||
+ | |Ray Doeksen | ||
+ | |Danger Committee | ||
+ | |- | ||
+ | |Michael Skilton | ||
+ | |Danger Committee | ||
|- | |- | ||
|} | |} | ||
− | |||
==Documentation== | ==Documentation== | ||
− | + | The following is a work in progress. | |
+ | https://wiki.pumpingstationone.org/Wood_Lathe_Authorization_Checklist | ||
[[Category:Woodworking]] | [[Category:Woodworking]] | ||
[[Category:Shop Equipment]] | [[Category:Shop Equipment]] |
Revision as of 13:27, 29 October 2014
Owner/Loaner | Joe Nudell |
---|---|
Serial Number | NAN |
Make/Model | Jet 1236 |
Arrival Date | 6/1/14 |
Usability | yes |
Contact | Joe Nudell |
Where | Woodshop |
Authorization Needed | yes |
Hackable | no |
Estimated Value | 800 |
Host Area | {{{hostarea}}} |
This tool requires certification for use.
Personal Protective Equipment
- Face shield (not just safety glasses) must be worn.
- Long and loose hair must be contained.
- Do not wear gloves or loose clothing.
- Remove watches, rings, and other jewelry.
- Don't wear or roll up long sleeves.
- Dust protection may be required.
Pre-Operational Safety Checks
- Locate and ensure you are familiar with all machine operations and controls.
- Ensure all guards are fitted, secure and functional. Do not operate if guards are missing or faulty.
- Workpiece must be securely fastened to face plate, chuck or between centers.
- Rotate the workpiece by hand to check clearance between tool rest and bed.
- Ensure the cutting tools are sharp and in good condition.
- Start the dust extraction unit before using the machine.
- Make sure all clamping handles are tight.
Operational Safety Checks
- Adjust speed to suit the diameter of the work and turning operation (IMPORTANT - *never* adjust speed while the lathe is off!)
- Before making adjustments (apart from speed), switch off and bring the machine to a complete standstill.
- Keep the tool rest adjusted close to the work and at the correct height.
- Stop the lathe and remove all tool rests before sanding.
Ending Operations and Cleaning Up
- Switch off the machine when work completed.
- Return all chisels and other tools to racks.
- Leave the machine in a safe, clean and tidy state.
Potential Hazards and Injuries
- Eye injuries from flying debris or defective timber.
- Hair/clothing getting caught in moving machine parts.
- Airborne dust.
Do
- Rough cut the workpiece as close as possible to the finished shape before installing it.
- Check your workpiece for flaws, cracks, knots etc. and test glue joints before mounting the workpiece on machine.
- Use the lowest speed when starting a new workpiece.
Don't
- Drive the workpiece into the drive center while the drive center is in the headstock.
- Set the drive center into the workpiece with a soft mallet prior to installing it on the headstock.
- Touch your project by hand while the lathe is running
How To Get Certified
The area host has determined that certifications for this machine should not be viral.
A list of members allowed to certify others will be posted here when the Danger Committee has finish creating a process.
List of Currently Certified Users
Qualified Member | Trained By |
---|---|
Matt Triano | Danger Committee |
Joeseph Nudell | Danger Committee/Owner |
Jason Shanfield | Danger Committee |
Ray Doeksen | Danger Committee |
Michael Skilton | Danger Committee |
Documentation
The following is a work in progress. https://wiki.pumpingstationone.org/Wood_Lathe_Authorization_Checklist