Difference between revisions of "Jet Wood Lathe"
| Line 1: | Line 1: | ||
| + | {{delete|the equipment is no longer at the space}} | ||
| + | |||
{{Template:EquipmentPage | {{Template:EquipmentPage | ||
|image = | |image = | ||
| Line 7: | Line 9: | ||
|model = Jet 1236 | |model = Jet 1236 | ||
|arrived = 6/1/14 | |arrived = 6/1/14 | ||
| − | |doesitwork = | + | |doesitwork = no |
|contact = Joe Nudell | |contact = Joe Nudell | ||
|where = Woodshop | |where = Woodshop | ||
| Line 14: | Line 16: | ||
}} | }} | ||
'''This tool requires certification for use.''' | '''This tool requires certification for use.''' | ||
| + | |||
| + | == Status == | ||
| + | |||
| + | The Jet Wood Lathe has been removed from the space by its owner. It is no longer available for use, so it is listed as "not working." | ||
| + | |||
== Personal Protective Equipment == | == Personal Protective Equipment == | ||
Revision as of 19:07, 5 September 2015
 | This page is a candidate for deletion. The given reason is: the equipment is no longer at the space
This notice should remain for a minimum of 1 week after it was placed on the page. If discussion is still ongoing, it should remain until a consensus is reached, after which the page will either be deleted or this notice removed. If you disagree with its deletion, please discuss your reasons on this page or on its associated talk page, as applicable. Remember to check if anything links here and the page history before deleting. Help delete other pages by visting Category:Candidates_for_deletion Last edit by Rdoeksen (talk · contrib) · Last edited on Sat, 05 Sep 2015 19:07:53 +0000 |
 | This tool is currently broken, please contact the area host for more information. |
| Owner/Loaner | Joe Nudell |
|---|---|
| Serial Number | NAN |
| Make/Model | Jet 1236 |
| Arrival Date | 6/1/14 |
| Usability | no |
| Contact | Joe Nudell |
| Where | Woodshop |
| Authorization Needed | yes |
| Hackable | no |
| Estimated Value | 800 |
| Host Area | {{{hostarea}}} |
This tool requires certification for use.
Status
The Jet Wood Lathe has been removed from the space by its owner. It is no longer available for use, so it is listed as "not working."
Personal Protective Equipment
- Face shield (not just safety glasses) must be worn.
- Long and loose hair must be contained.
- Do not wear gloves or loose clothing.
- Remove watches, rings, and other jewelry.
- Don't wear or roll up long sleeves.
- Dust protection may be required.
Pre-Operational Safety Checks
- Locate and ensure you are familiar with all machine operations and controls.
- Ensure all guards are fitted, secure and functional. Do not operate if guards are missing or faulty.
- Workpiece must be securely fastened to face plate, chuck or between centers.
- Rotate the workpiece by hand to check clearance between tool rest and bed.
- Ensure the cutting tools are sharp and in good condition.
- Start the dust extraction unit before using the machine.
- Make sure all clamping handles are tight.
Operational Safety Checks
- Adjust speed to suit the diameter of the work and turning operation (IMPORTANT - *never* adjust speed while the lathe is off!)
- Before making adjustments (apart from speed), switch off and bring the machine to a complete standstill.
- Keep the tool rest adjusted close to the work and at the correct height.
- Stop the lathe and remove all tool rests before sanding.
Ending Operations and Cleaning Up
- Switch off the machine when work completed.
- Return all chisels and other tools to racks.
- Leave the machine in a safe, clean and tidy state.
Potential Hazards and Injuries
- Eye injuries from flying debris or defective timber.
- Hair/clothing getting caught in moving machine parts.
- Airborne dust.
Do
- Rough cut the workpiece as close as possible to the finished shape before installing it.
- Check your workpiece for flaws, cracks, knots etc. and test glue joints before mounting the workpiece on machine.
- Use the lowest speed when starting a new workpiece.
Don't
- Drive the workpiece into the drive center while the drive center is in the headstock.
- Set the drive center into the workpiece with a soft mallet prior to installing it on the headstock.
- Touch your project by hand while the lathe is running
How To Get Certified
The area host has determined that certifications for this machine should not be viral.
A list of members allowed to certify others will be posted here when the Danger Committee has finish creating a process.
List of Currently Certified Users
| Qualified Member | Trained By |
|---|---|
| Joeseph Nudell | Danger Committee/Owner |
| Jason Shanfield | Danger Committee |
| Ray Doeksen | Danger Committee |
| Michael Skilton | Danger Committee |
| Patrick Grider | Danger Committee |
| Matt Triano | Patrick Grider |
Documentation
The following is a work in progress. https://wiki.pumpingstationone.org/Wood_Lathe_Authorization_Checklist