Difference between revisions of "Jet Wood Lathe"

From Pumping Station: One Wiki
Jump to: navigation, search
Line 1: Line 1:
{{delete|the equipment is no longer at the space}}
 
  
 
{{Template:EquipmentPage
 
{{Template:EquipmentPage
 
|image =  
 
|image =  
|owner = Joe Nudell
+
|owner = David Rubman
 
|serial = NAN  
 
|serial = NAN  
 
|certification = yes
 
|certification = yes
 
|hackable = no
 
|hackable = no
 
|model = Jet 1236
 
|model = Jet 1236
|arrived = 6/1/14
+
|arrived = 11/21/2015
 
|doesitwork = no
 
|doesitwork = no
|contact = Joe Nudell
+
|contact = David Rubman
 
|where = Woodshop
 
|where = Woodshop
 
|value = 800
 
|value = 800
Line 19: Line 18:
 
== Status ==
 
== Status ==
  
The Jet Wood Lathe has been removed from the space by its owner. It is no longer available for use, so it is listed as "not working."
+
The Jet Wood Lathe hasn't been put in service yet, so it is listed as "not working."
  
 
== Personal Protective Equipment ==
 
== Personal Protective Equipment ==
Line 75: Line 74:
 
! Trained By
 
! Trained By
 
|-
 
|-
|Joeseph Nudell
+
|
|Danger Committee/Owner
+
|
 
|-
 
|-
|Jason Shanfield
+
|
|Danger Committee
+
|
 
|-
 
|-
|Ray Doeksen
+
|
|Danger Committee
+
|
 
|-
 
|-
|Michael Skilton
+
|
|Danger Committee
+
|
 
|-
 
|-
|Patrick Grider
+
|
|Danger Committee
+
|
 
|-
 
|-
|Matt Triano
+
|  
|Patrick Grider
+
|
 
|-
 
|-
 
|}
 
|}

Revision as of 08:40, 4 February 2016


Jet Wood Lathe
Owner/Loaner David Rubman
Serial Number NAN
Make/Model Jet 1236
Arrival Date 11/21/2015
Usability no
Contact David Rubman
Where Woodshop
Authorization Needed yes
Hackable no
Estimated Value 800
Host Area {{{hostarea}}}


Jet Wood Lathe David Rubman Area: {{{hostarea}}} https://wiki.pumpingstationone.org/Jet_Wood_Lathe



This tool requires certification for use.

Status

The Jet Wood Lathe hasn't been put in service yet, so it is listed as "not working."

Personal Protective Equipment

  • Face shield (not just safety glasses) must be worn.
  • Long and loose hair must be contained.
  • Do not wear gloves or loose clothing.
  • Remove watches, rings, and other jewelry.
  • Don't wear or roll up long sleeves.
  • Dust protection may be required.

Pre-Operational Safety Checks

  • Locate and ensure you are familiar with all machine operations and controls.
  • Ensure all guards are fitted, secure and functional. Do not operate if guards are missing or faulty.
  • Workpiece must be securely fastened to face plate, chuck or between centers.
  • Rotate the workpiece by hand to check clearance between tool rest and bed.
  • Ensure the cutting tools are sharp and in good condition.
  • Start the dust extraction unit before using the machine.
  • Make sure all clamping handles are tight.

Operational Safety Checks

  • Adjust speed to suit the diameter of the work and turning operation (IMPORTANT - *never* adjust speed while the lathe is off!)
  • Before making adjustments (apart from speed), switch off and bring the machine to a complete standstill.
  • Keep the tool rest adjusted close to the work and at the correct height.
  • Stop the lathe and remove all tool rests before sanding.

Ending Operations and Cleaning Up

  • Switch off the machine when work completed.
  • Return all chisels and other tools to racks.
  • Leave the machine in a safe, clean and tidy state.

Potential Hazards and Injuries

  • Eye injuries from flying debris or defective timber.
  • Hair/clothing getting caught in moving machine parts.
  • Airborne dust.

Do

  • Rough cut the workpiece as close as possible to the finished shape before installing it.
  • Check your workpiece for flaws, cracks, knots etc. and test glue joints before mounting the workpiece on machine.
  • Use the lowest speed when starting a new workpiece.

Don't

  • Drive the workpiece into the drive center while the drive center is in the headstock.
    • Set the drive center into the workpiece with a soft mallet prior to installing it on the headstock.
  • Touch your project by hand while the lathe is running

How To Get Certified

The area host has determined that certifications for this machine should not be viral.

A list of members allowed to certify others will be posted here when the Danger Committee has finish creating a process.

List of Currently Certified Users

Qualified Member Trained By

Documentation

The following is a work in progress. https://wiki.pumpingstationone.org/Wood_Lathe_Authorization_Checklist