Jet Wood Lathe

Jet Wood Lathe

Owner/Loaner	David Rubman
Serial Number	NAN
Make/Model	Jet 1236
Arrival Date	11/21/2015
Usability	yes
Contact	David Rubman
Where	Woodshop
Authorization Needed	yes
Hackable	no
Estimated Value	800
Host Area	woodworking

Authorization for this tool by authorized proctors only

This tool requires certification for use.

Authorized Proctors

This tool requires certification for use. Please contact one of the following to arrange authorization.

• This list is a basic starting point pending approval of the area host.

Proctor	Contact
Matt Triano	matt.triano @ gmail.com
Eric Beauchamp — area host	eric @ home-chicago.com
Sevin Strauss — approved authorizer
Andrew Camardella — approved authorizer

Resources

Wood Lathe Authorization Checklist

Intro to Woodturning by Brian Clifford

Woodturning Reddit Wiki

Personal Protective Equipment

• Face shield (not just safety glasses) must be worn.
• Long and loose hair must be contained.
• Do not wear gloves or loose clothing.
• Remove watches, rings, and other jewelry.
• Roll up or don't wear long sleeves.
• Dust protection may be required.

Pre-Operational Safety Checks

• Locate and ensure you are familiar with all machine operations and controls.
• Ensure all guards are fitted, secure and functional. Do not operate if guards are missing or faulty.
• Workpiece must be securely fastened to face plate, chuck or between centers.
• Rotate the workpiece by hand to check clearance between tool rest and bed.
• Ensure the cutting tools are sharp and in good condition.
• Start the dust extraction unit before using the machine.
• Make sure all clamping handles are tight.

Operational Safety Checks

• Adjust speed to suit the diameter of the work and turning operation (IMPORTANT - *never* adjust speed while the lathe is off!)
• Before making adjustments (apart from speed), switch off and bring the machine to a complete standstill.
• Keep the tool rest adjusted close to the work and at the correct height.
• Stop the lathe and remove all tool rests before sanding.

Ending Operations and Cleaning Up

• Switch off the machine when work completed.
• Return all chisels and other tools to racks.
• Leave the machine in a safe, clean and tidy state.
• Sweep or vacuum any wood debris/dust/shavings.

Potential Hazards and Injuries

• Eye injuries from flying debris or defective timber.
• Hair/clothing getting caught in moving machine parts.
• Airborne dust.

Do

• Rough cut the workpiece as close as possible to the finished shape before installing it.
• Check your workpiece for flaws, cracks, knots etc. and test glue joints before mounting the workpiece on machine.
• Use the lowest speed when starting a new workpiece.

Don't

• Drive the workpiece into the drive center while the drive center is in the headstock.
  • Set the drive center into the workpiece with a soft mallet prior to installing it on the headstock.
• Touch your project by hand while the lathe is running

How To Get Certified

The area host has determined that certifications for this machine should not be viral.

A list of members allowed to certify others will be posted here when the Danger Committee has finish creating a process.

List of Currently Certified Users

Qualified Member	Trained By	Auth Date
Matt Triano	Patrick Grider
Sevin Straus	Danger Committee
Eric Beauchamp	Danger Committee
Erik Wessing	Danger Committee
Andrew Camardella	Danger Committee
Ray Doeksen	Danger Committee
Michael Skilton	Danger Committee
Daron Wooding	Andrew Camardella
Sam Paris	Andrew Camardella	2016-07-20
Donald Wells	Andrew Camardella	2016-07-20
McTavish McArdle	Andrew Camardella	2016-07-20
An Phan	Andrew Camardella	2016-08-18
Matt Keith	Andrew Camardella	2016-08-18
Ian Monroe	Andrew Camardella	2016-07-20
Les Schier	Devin Straus	2016-09-01

Documentation

The following is a work in progress. https://wiki.pumpingstationone.org/Wood_Lathe_Authorization_Checklist

Manual https://wiki.pumpingstationone.org/File:Jet_1236.pdf

File:Oneway Chuck Manual.pdf