Difference between revisions of "LeBlond Regal"

From Pumping Station One
Jump to navigation Jump to search
VisualWikitext
 
(94 intermediate revisions by 12 users not shown)
Line 13: Line 13:
 
| image = LeBlond.JPG
 
| image = LeBlond.JPG
 
| owner = PS1
 
| owner = PS1
−
| serial = C6 1319
+
| serial = 6C 1319
 
| model = LeBlond Regal
 
| model = LeBlond Regal
 
| arrived = May 2018
 
| arrived = May 2018
Line 37: Line 37:
  
 
== Specifications ==
 
== Specifications ==
 +
 +
Swing over bed 15 1/2 "
 +
Length of bed 54"
 +
Power required - 220 3 ph 30a ckt
 +
 +
NOTE: The manual specifies SAE 20 oil, it is the same as ISO 68 or Way oil
  
 
== Auth/Use Notes ==
 
== Auth/Use Notes ==
 +
 +
The following are prerequisites for authorization on the LeBlond
 +
1 Tier 1 Cold Metals authorization
 +
2 Canvas LeBlond course
 +
 +
 +
Base skills for authorization:
 +
  1. Safety
 +
  2. Power, fwd, neutral, break, rev
 +
  3. Basic maintenance - Oil ports, oiler
 +
  4. Familiarity with controls - Z axis, Y axis, compound, auto feed, speeds
 +
  5. 3 jaw chuck
 +
  6. Tool post, tool selection
 +
  7. Face cut
 +
  8. Tail stock support
 +
  9. Longitudinal cut, cut to size
 +
  10. Cleanup
  
 
== To-Do ==
 
== To-Do ==
 +
{| class="wikitable" border="1"
 +
! Status
 +
! Item
 +
! Person Working on Item
 +
! Comments
 +
|-
 +
|  closed
 +
| Should we replace hydraulic filter? It's not mentioned in the manual but it seems like something you may want to change?
 +
| Jim Brink
 +
|Per discussion Tuesday 5/29 we will top off resevoir and run as-is for a few months then replace oil
 +
|-
 +
|Closed
 +
|Top off oil reservoirs, oil machine  and follow maintenance in manual as far as I can tell all reservoirs should have ISO 68 (Way) oil.
 +
|
 +
|Will wait until next maintenance cycle
 +
|-
 +
|
 +
|Do we need some device to help lift chucks on removal ( they weigh approx 80#) a lightweight Harbor Freight hoist is about $70
 +
|Sevin Straus
 +
|Stuff to buy spreadsheet updated with the main items.
 +
Have found a rail and trolley setup that will hang from the rafters and support a 500# lifting capacity winch. 
 +
|-
 +
|done
 +
|Taper attachment needs to be cleaned and tested
 +
|Abel Greenwald
 +
|
 +
|-
 +
|Closed
 +
|Level and check for taper
 +
|Sevin Straus
 +
|Lathe is leveled but need to check for taper in a test cut
 +
-Test cuts have been made, and we are able to cut an actual round, non tapered, cut to measure first, and created a dead(ish) center for the headstock.  We used our new center along with the live center we have to measure the general alignment between the headstock and the tailstock.  The gauge bar had a .003" slope over 24".  However we were able to get .003" flex on the live center, and that bar weighs 20+lbs so not too bad.  On the side to side alignment, there was a .001" taper over 24" with the tailstock being slightly closer to the operator than the headstock.  Abel and I did not try to chase that .001" out on Saturday, but if we feel that is too much error we can take a crack at it.
 +
|-
 +
|done
 +
|Any tooling needed?
 +
|
 +
|Need 5/8" indexable cutting set
 +
|-
 +
|done
 +
|Tool post attachment?
 +
|Jim Brink
 +
|
 +
|-
 +
|Hold
 +
|Do we want to fit a DRO? NOTE: the Cold metals budget is getting tight for this tool we may budget this in 2019
 +
|
 +
|Possibly put together a vote to finance this and the guard.
 +
|-
 +
|
 +
|Do we want to fit cooling?
 +
|Ed Bennett
 +
|Spec out a pump system for Jim to purchase, Ed will install.
 +
|-
 +
|
 +
|Carrage lock nofunctional
 +
|
 +
|
 +
|-
 +
|
 +
|Signage and Marking on and around the Leblonde
 +
|
 +
|
 +
|-
 +
|
 +
|Authorization path
 +
|
 +
|
 +
|-
 +
|
 +
|Add Estop - Kickplate plus switch
 +
|Ed Bennett
 +
|Spoke to Roger (888-532-5663) LeBlond does not have a product or document to retrofit this machine 5/30
 +
|-
 +
|done
 +
|Need to mount a guard
 +
|
 +
|Possible solution: https://atssafety.com/collections/lathe-guards/products/lathe-safety-guards-sliding-lathe-guard-gear-case-mount
 +
|-
 +
|
 +
|Fencing for Spectators and Floor taping
 +
|
 +
|
 +
|-
 +
|todo
 +
|Ensure Chucks are true and with in spec
 +
|
 +
|
 +
|-
 +
|done
 +
|purchase 3mt dead center
 +
|
 +
|
 +
|-
 +
|todo
 +
|Clean taper attachment and saddle (cross slide, compound)
 +
|
 +
|
 +
|-
 +
|todo
 +
|repair saddle lock
 +
|
 +
|
 +
|-
 +
|todo
 +
|Adjust gibs on saddle
 +
|
 +
|
 +
|}
  
 
== Maintenance ==
 
== Maintenance ==
 +
 +
Removing the chuck. This video shows some interesting pointers about seating the chuck    : https://www.youtube.com/watch?v=tsM1pRpTciY
 +
 +
If you find problems with the high speeds check the coged belt in the headstock ( 27" 54t 1" wide  McMaster Part: https://www.mcmaster.com/6484k172  To replace the belt remove the four screws holding the retaining ring and the retaining ring from the coged gear, work the belt out, it can be removed without removing any other gears.
  
 
== Equipment ==
 
== Equipment ==
  
 +
Jacobs Spindle Nose Collet Chuck " A very nice piece of tooling", this video is worth it for the music alone - https://www.youtube.com/watch?v=smKWlrjxXag
  
−
Tool Holders;
+
Shars Tool set available: 
−
  1) Dorian Tool STNC, Right Hand Cut, 3° Lead Angle, 5/8" Shank Height x 5/8" Shank Width, Indexable Turning Toolholder  4" OAL, Screw Holding Method
+
<gallery>
−
          MSC Part #: 47145917 Mfr Part #: 73310151738
+
File:404-1054main_2.jpg|SHARS Sku 404-1054
−
      Uses Insert- Insert Inscribed Circle (Inch) 1/4 Style N, 3 degree TCMT 1/4 LC
+
File:404-1054sketch.jpg|
−
      https://www.mscdirect.com/product/details/47145917?orderedAs=73310151738&rd=k&searchAhead=true&searchAheadTerm=73310151738&        typahddsp=73310151738%20(MSC%20%2347145917)&hdrsrh=true
+
File:404-1056Main.jpg|DCMT3 Insert SHARS Sku 404-1060
−
 
+
File:404-1061Main.jpg|CCMT3 Carbide Insert SHARS Sku 404-1061
−
   2) Dorian Tool .59" Min Bore Diam, 1/2" Shank Diam, 6" OAL, STCMB Indexable Boring Bar 1-1/2" Max Bore Depth, Screw Holding Method
+
File:404-1069Main.jpg|WCMX Carbide Insert SHARS Sku 404-1069
−
      Uses Insert- Insert Inscribed Circle (Inch) 1/4 Style N, 3 degree TCMT 1/4 LC
+
File:424-1381Main.jpg|AG60 External V Partial Profile AG60 Carbide Threading SHARS Sku 424-1381
−
https://www.mscdirect.com/product/details/47146014?orderedAs=73310155740&rd=k&searchAhead=true&searchAheadTerm=73310155740&typahddsp=73310155740%20(MSC%20%2347146014)&hdrsrh=true
+
File:404-2346a.jpg|Boring Bar 3/4 uses DC## insert
 +
</gallery>
 +
Insert Tools:
 +
  SCLCL5/8  CCMT3 (SHARS SKU404-1061) 32.5 T15 M4x10
 +
  SCLCR5/8  CCMT3 (SHARS SHU404-1061) 32.5 T15 M4x10
 +
  SER5/8 -16 16ER    T15 M3.5x12 LT16R
 +
  SDNCN5/8  DCMT3 (SHARS SKU 404=1060) 32.5 T15 M4x10
 +
  SWGCR5/8  WCMX  (SHARS SkU 404-1069) 32.5 T15 M4x10
 +
  SDJCR5/8  DC** 32.5 T15 M4x10
 +
   MGEHR5/8-3  MGMN300 32.5 T15 M4x10
 +
  boring bar Shars S12S-SDUCR3 3/4"x 1.25" uses DC##32.5 insert T15 M4x10 screw
  
 
== References ==
 
== References ==
  
 
Manual -> https://wiki.pumpingstationone.org/images/LeBlond_Regal.pdf
 
Manual -> https://wiki.pumpingstationone.org/images/LeBlond_Regal.pdf
 +
 +
Schematic ->  https://wiki.pumpingstationone.org/images/EE700_Electrical_Drawings.pdf
 +
 +
Schematic with changes for E Switch -> https://wiki.pumpingstationone.org/images/LeBlond_w_E_Switch_Small.jpg ‎
  
 
== List of Currently Authorized Users ==
 
== List of Currently Authorized Users ==
Line 66: Line 216:
 
! Trained By
 
! Trained By
 
!Date Trained
 
!Date Trained
 +
!Comments
 +
|-
 +
|Charles Ware
 +
|Jim Brink
 +
|8/3/19
 +
|
 
|-
 
|-
−
|  
+
|Ryan Pierce
−
|  
+
|Jim Brink
 +
|8/7/19
 
|
 
|
 
|-
 
|-
−
|
+
|Bill Hunt
 +
|Jim Brink
 +
|8/24/19
 
|
 
|
 +
|-
 +
|[[User:mct|McTavish McArdle]]
 +
|Jim Brink
 +
|2019-10-19
 +
|
 +
|-
 +
|[[User:rchace|Raymond Chace]]
 +
|Jim Brink
 +
|11/16/19
 +
|
 +
|-
 +
|[[User:sranjb2|Shayan Ranjbari]]
 +
|Jim Brink
 +
|07/25/2020
 +
|-
 +
|[[User:tcummings|Tom Cummings]]
 +
|Jim Brink
 +
|10/17/2020
 +
|
 +
|-
 +
|}
 +
[[Category:Shop Equipment]]
 +
[[Category:Equipment]]
 
[[Category: Cold Metals]]
 
[[Category: Cold Metals]]

Latest revision as of 14:20, 29 October 2021


LeBlond Regal
LeBlond.JPG
Owner/Loaner PS1
Serial Number 6C 1319
Make/Model LeBlond Regal
Arrival Date May 2018
Usability Yes
Contact Host Cold Metals
Where Cold Metals
Authorization Needed Yes
Hackable No
Estimated Value 5000
Host Area Cold Metals


LeBlond Regal PS1 Area: {{{hostarea}}} https://wiki.pumpingstationone.org/wiki/LeBlond_Regal



Specifications

Swing over bed 15 1/2 " Length of bed 54" Power required - 220 3 ph 30a ckt

NOTE: The manual specifies SAE 20 oil, it is the same as ISO 68 or Way oil

Auth/Use Notes

The following are prerequisites for authorization on the LeBlond 

1 Tier 1 Cold Metals authorization
2 Canvas LeBlond course


Base skills for authorization: 

  1. Safety
  2. Power, fwd, neutral, break, rev
  3. Basic maintenance - Oil ports, oiler
  4. Familiarity with controls - Z axis, Y axis, compound, auto feed, speeds
  5. 3 jaw chuck
  6. Tool post, tool selection
  7. Face cut
  8. Tail stock support
  9. Longitudinal cut, cut to size
  10. Cleanup

To-Do

Status Item Person Working on Item Comments
closed Should we replace hydraulic filter? It's not mentioned in the manual but it seems like something you may want to change? Jim Brink Per discussion Tuesday 5/29 we will top off resevoir and run as-is for a few months then replace oil
Closed Top off oil reservoirs, oil machine and follow maintenance in manual as far as I can tell all reservoirs should have ISO 68 (Way) oil. Will wait until next maintenance cycle
Do we need some device to help lift chucks on removal ( they weigh approx 80#) a lightweight Harbor Freight hoist is about $70 Sevin Straus Stuff to buy spreadsheet updated with the main items.

Have found a rail and trolley setup that will hang from the rafters and support a 500# lifting capacity winch.

done Taper attachment needs to be cleaned and tested Abel Greenwald
Closed Level and check for taper Sevin Straus Lathe is leveled but need to check for taper in a test cut

-Test cuts have been made, and we are able to cut an actual round, non tapered, cut to measure first, and created a dead(ish) center for the headstock. We used our new center along with the live center we have to measure the general alignment between the headstock and the tailstock. The gauge bar had a .003" slope over 24". However we were able to get .003" flex on the live center, and that bar weighs 20+lbs so not too bad. On the side to side alignment, there was a .001" taper over 24" with the tailstock being slightly closer to the operator than the headstock. Abel and I did not try to chase that .001" out on Saturday, but if we feel that is too much error we can take a crack at it.

done Any tooling needed? Need 5/8" indexable cutting set
done Tool post attachment? Jim Brink
Hold Do we want to fit a DRO? NOTE: the Cold metals budget is getting tight for this tool we may budget this in 2019 Possibly put together a vote to finance this and the guard.
Do we want to fit cooling? Ed Bennett Spec out a pump system for Jim to purchase, Ed will install.
Carrage lock nofunctional
Signage and Marking on and around the Leblonde
Authorization path
Add Estop - Kickplate plus switch Ed Bennett Spoke to Roger (888-532-5663) LeBlond does not have a product or document to retrofit this machine 5/30
done Need to mount a guard Possible solution: https://atssafety.com/collections/lathe-guards/products/lathe-safety-guards-sliding-lathe-guard-gear-case-mount
Fencing for Spectators and Floor taping
todo Ensure Chucks are true and with in spec
done purchase 3mt dead center
todo Clean taper attachment and saddle (cross slide, compound)
todo repair saddle lock
todo Adjust gibs on saddle

Maintenance

Removing the chuck. This video shows some interesting pointers about seating the chuck : https://www.youtube.com/watch?v=tsM1pRpTciY

If you find problems with the high speeds check the coged belt in the headstock ( 27" 54t 1" wide McMaster Part: https://www.mcmaster.com/6484k172 To replace the belt remove the four screws holding the retaining ring and the retaining ring from the coged gear, work the belt out, it can be removed without removing any other gears.

Equipment

Jacobs Spindle Nose Collet Chuck " A very nice piece of tooling", this video is worth it for the music alone - https://www.youtube.com/watch?v=smKWlrjxXag

Shars Tool set available:

  • SHARS Sku 404-1054

  • 404-1054sketch.jpg

  • DCMT3 Insert SHARS Sku 404-1060

  • CCMT3 Carbide Insert SHARS Sku 404-1061

  • WCMX Carbide Insert SHARS Sku 404-1069

  • AG60 External V Partial Profile AG60 Carbide Threading SHARS Sku 424-1381

  • Boring Bar 3/4 uses DC## insert 

Insert Tools:
 SCLCL5/8  CCMT3 (SHARS SKU404-1061) 32.5 T15 M4x10
 SCLCR5/8  CCMT3 (SHARS SHU404-1061) 32.5 T15 M4x10
 SER5/8 -16 16ER     T15 M3.5x12 LT16R
 SDNCN5/8  DCMT3 (SHARS SKU 404=1060) 32.5 T15 M4x10
 SWGCR5/8  WCMX  (SHARS SkU 404-1069) 32.5 T15 M4x10
 SDJCR5/8  DC** 32.5 T15 M4x10
 MGEHR5/8-3  MGMN300 32.5 T15 M4x10
 boring bar Shars S12S-SDUCR3 3/4"x 1.25" uses DC##32.5 insert T15 M4x10 screw

References

Manual -> https://wiki.pumpingstationone.org/images/LeBlond_Regal.pdf

Schematic -> https://wiki.pumpingstationone.org/images/EE700_Electrical_Drawings.pdf

Schematic with changes for E Switch -> https://wiki.pumpingstationone.org/images/LeBlond_w_E_Switch_Small.jpg ‎

List of Currently Authorized Users

Qualified Member Trained By Date Trained Comments
Charles Ware Jim Brink 8/3/19
Ryan Pierce Jim Brink 8/7/19
Bill Hunt Jim Brink 8/24/19
McTavish McArdle Jim Brink 2019-10-19
Raymond Chace Jim Brink 11/16/19
Shayan Ranjbari Jim Brink 07/25/2020
Tom Cummings Jim Brink 10/17/2020
Retrieved from "https://ps1.mywikis.wiki/w/index.php?title=LeBlond_Regal&oldid=44321"