Difference between revisions of "Prusa i3 MK2S .203 3D Printer"
m (added instructions to post-printing section) |
|||
| (7 intermediate revisions by 6 users not shown) | |||
| Line 8: | Line 8: | ||
|arrived = 12/2017 | |arrived = 12/2017 | ||
|where = CNC Area, downstairs | |where = CNC Area, downstairs | ||
| − | |doesitwork = | + | |doesitwork = yes |
|contact = CNC Area Host | |contact = CNC Area Host | ||
|value = $500 | |value = $500 | ||
|image = | |image = | ||
}} | }} | ||
| + | |||
| + | == Description == | ||
| + | There are currently three of these at PS1, the other two being [https://wiki.pumpingstationone.org/Prusa_i3_MK2S_.202 .202] and [http://wiki.pumpingstationone.org/Prusa_i3_MK2S_.204 .204]. | ||
== Status == | == Status == | ||
| − | 12/10/2017 - | + | 12/10/2017 - Still Need to Configure Octoprint. Can print via SD Card. |
== Operation == | == Operation == | ||
| − | === [[Prusa i3 OctoPrint Server]] | + | ===1. Prepare the Printer=== |
| + | ====''1a. Clean the nozzle''==== | ||
| + | |||
| + | put info here | ||
| + | |||
| + | ====''1b. Check/Load material spool''==== | ||
| + | Remove existing spool, if necessary. | ||
| + | |||
| + | put more info here. | ||
| + | |||
| + | ====''1c. Clean the bed''==== | ||
| + | put info here | ||
| + | |||
| + | ====''1d. Set printer settings for your job''==== | ||
| + | put info here - note: for the 203 OctoPrint printer, you can control & monitor bed & nozzle temps | ||
| + | |||
| + | ===2. Prepare Your .STL file=== | ||
| + | Put info about Prusa Slicer here... | ||
| + | |||
| + | |||
| + | ===3. Upload & Print Your .STL File=== | ||
| + | |||
| + | ====''3(a). The Prusa i3 MK2S printers at IP address 10.100.1.202 and 10.100.1.204''==== | ||
| + | These two printers do not use OctoPrint. You must load your STL files directly onto the printer using SD Cards (some are provided at PS1). | ||
| + | |||
| + | 3(a)1. Load your .STL file onto an SD card (some are provided at PS1). | ||
| + | |||
| + | 3(a)2. Insert SD card into printer. | ||
| + | |||
| + | 3(a)3. Then...[put info here] | ||
| + | |||
| + | ====''3(b). The Prusa i3 MK2S printer at IP address 10.100.1.203 (OctoPrint)''==== | ||
| + | This printer uses the '''[[Prusa i3 OctoPrint Server]]''' to manage the print job queue. Note the SD Card reader in this printer may not work [confirm]. | ||
| + | |||
| + | 3(b)1. Open a web browser connected to a computer/device on the PS1 network & enter 10.100.1.203 in the IP address field. | ||
| + | Note: If printer has been turned off, you may need to first select "Connect" under the left side Connection tab if the printer has been turned off. '''All settings to connect are retained and should not be modified.''' | ||
| + | |||
| + | 3(b)2. Warm up the printer (if you haven't already) using the controls on the Temperature tab -- enter a temperature in Celsius and click "Set" | ||
| + | |||
| + | 3(b)3. Set printer's feed & flow rates, as well as fan settings (if you haven't already done so on the printer). You can control the printer' movements & extrusion in the 'Control' tab. | ||
| + | |||
| + | 3(b)4. Upload STL file using the left side "Files" tab. | ||
| + | |||
| + | 3(b)5. Find the STL you uploaded and click the "Slice" button (it looks like a magic wand). Note: Cura is the default slicing engine. | ||
| + | |||
| + | 3(b)6. Select one of the preset slicing profiles, and then manually set your preferred temperatures and speeds using the Basic and Advanced tabs. This will generate G-Code, exporting a GCO file. | ||
| + | |||
| + | 3(b)7. Locate your GCO (G-Code) file in the Files tab on the left side. Click 'Load and Print' to print your object. | ||
| + | |||
| + | ''This is only a high level overview of how to use OctoPrint. If you are already authorized but have not used OctoPrint, feel free to attend future authorization sessions. OctoPrint will accept g-code from the most popular slicers such as Cura, Slic3r, Repetier-Host, and Simplify3D.'' | ||
| − | + | ===4. Post-Printing=== | |
| + | After your printing is complete, reheat, remove print, & clean. | ||
| − | + | ====''4a. Delete your files''==== | |
| + | Delete your files from the OctoPrint server and/or borrowed SD cards. You can download your GCO file for future printing if you would like to retain the specific sliced project. | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | === Troubleshooting === | |
| + | Refer to our [[3D Print Troubleshooting]] page. | ||
Latest revision as of 19:48, 22 February 2022
| Owner/Loaner | PS:One |
|---|---|
| Serial Number | SERIAL NUMBER |
| Make/Model | Prusa i3 MK2S |
| Arrival Date | 12/2017 |
| Usability | yes |
| Contact | CNC Area Host |
| Where | CNC Area, downstairs |
| Authorization Needed | yes |
| Hackable | no |
| Estimated Value | $500 |
| Host Area | CNC |
Description
There are currently three of these at PS1, the other two being .202 and .204.
Status
12/10/2017 - Still Need to Configure Octoprint. Can print via SD Card.
Operation
1. Prepare the Printer
1a. Clean the nozzle
put info here
1b. Check/Load material spool
Remove existing spool, if necessary.
put more info here.
1c. Clean the bed
put info here
1d. Set printer settings for your job
put info here - note: for the 203 OctoPrint printer, you can control & monitor bed & nozzle temps
2. Prepare Your .STL file
Put info about Prusa Slicer here...
3. Upload & Print Your .STL File
3(a). The Prusa i3 MK2S printers at IP address 10.100.1.202 and 10.100.1.204
These two printers do not use OctoPrint. You must load your STL files directly onto the printer using SD Cards (some are provided at PS1).
3(a)1. Load your .STL file onto an SD card (some are provided at PS1).
3(a)2. Insert SD card into printer.
3(a)3. Then...[put info here]
3(b). The Prusa i3 MK2S printer at IP address 10.100.1.203 (OctoPrint)
This printer uses the Prusa i3 OctoPrint Server to manage the print job queue. Note the SD Card reader in this printer may not work [confirm].
3(b)1. Open a web browser connected to a computer/device on the PS1 network & enter 10.100.1.203 in the IP address field.
Note: If printer has been turned off, you may need to first select "Connect" under the left side Connection tab if the printer has been turned off. All settings to connect are retained and should not be modified.
3(b)2. Warm up the printer (if you haven't already) using the controls on the Temperature tab -- enter a temperature in Celsius and click "Set"
3(b)3. Set printer's feed & flow rates, as well as fan settings (if you haven't already done so on the printer). You can control the printer' movements & extrusion in the 'Control' tab.
3(b)4. Upload STL file using the left side "Files" tab.
3(b)5. Find the STL you uploaded and click the "Slice" button (it looks like a magic wand). Note: Cura is the default slicing engine.
3(b)6. Select one of the preset slicing profiles, and then manually set your preferred temperatures and speeds using the Basic and Advanced tabs. This will generate G-Code, exporting a GCO file.
3(b)7. Locate your GCO (G-Code) file in the Files tab on the left side. Click 'Load and Print' to print your object.
This is only a high level overview of how to use OctoPrint. If you are already authorized but have not used OctoPrint, feel free to attend future authorization sessions. OctoPrint will accept g-code from the most popular slicers such as Cura, Slic3r, Repetier-Host, and Simplify3D.
4. Post-Printing
After your printing is complete, reheat, remove print, & clean.
4a. Delete your files
Delete your files from the OctoPrint server and/or borrowed SD cards. You can download your GCO file for future printing if you would like to retain the specific sliced project.
Troubleshooting
Refer to our 3D Print Troubleshooting page.