Difference between revisions of "Supermax 25x2 Drum Sander"
Jump to navigation
Jump to search
Rebrendler (talk | contribs) (Created page with "{{Template:EquipmentPage |owner=PS:One |model=25x2 |serial=? |arrived= |doesitwork=yes |contact=Eric Beauchamp |where=Wood Shop |certification=yes |hackable...") |
Rebrendler (talk | contribs) |
||
| Line 22: | Line 22: | ||
|Eric Beauchamp | |Eric Beauchamp | ||
|Danger committee | |Danger committee | ||
| + | |6/23/2017 | ||
|- | |- | ||
|Ralph Brendler | |Ralph Brendler | ||
|Danger committee | |Danger committee | ||
| + | |6/23/2017 | ||
|- | |- | ||
|Paul van Lake | |Paul van Lake | ||
|Danger committee | |Danger committee | ||
| + | |6/23/2017 | ||
|} | |} | ||
| Line 33: | Line 36: | ||
== Notes == | == Notes == | ||
| + | *For oily or dense woods, take only very light passes to prevent clogging the sandpaper. | ||
| + | |||
| + | *Use a belt cleaner occasionally to refresh the sandpaper | ||
== Safety == | == Safety == | ||
| + | |||
| + | This sander features overload detection. If the machine detects too high a load, it will automatically slow down the feed. This saves wear and tear on the machine, but may cause burning of the workpiece if you cut too aggressively. | ||
| + | |||
| + | *The height adjustment on this machine is VERY aggressive. A full turn will raise the table by more than 2mm (a typical cut should be < .5mm). '''PLEASE USE A MAXIMUM OF 1/8 TURN OF THE HEIGHT WHEEL PER PASS!''' | ||
| + | |||
| + | * Make your first cuts with a very slow speed (10 or less). Once you are sure the load is OK you can gradually increase the speed on subsequent passes. | ||
| + | |||
| + | *When overload detection kicks in, a red light next to the speed control will turn on. '''IF YOU SEE THIS LIGHT, PLEASE REDUCE YOUR DEPTH OF CUT AND/OR FEED RATE!''' | ||
| + | |||
| + | *Like all of our other sanders, sleeves must be above the elbow, and no gloves should be worn. It's pretty easy to get pulled into the rollers. | ||
| + | |||
[[Category:Shop Equipment]] | [[Category:Shop Equipment]] | ||
Revision as of 02:13, 28 June 2017
 | |
| Owner/Loaner | PS:One |
|---|---|
| Serial Number | ? |
| Make/Model | 25x2 |
| Usability | yes |
| Contact | Eric Beauchamp |
| Where | Wood Shop |
| Authorization Needed | yes |
| Hackable | no |
| Estimated Value | $2700 |
| Host Area | Wood Shop |
| Qualified Member | Trained By | Date |
|---|---|---|
| Eric Beauchamp | Danger committee | 6/23/2017 |
| Ralph Brendler | Danger committee | 6/23/2017 |
| Paul van Lake | Danger committee | 6/23/2017 |
Notes
- For oily or dense woods, take only very light passes to prevent clogging the sandpaper.
- Use a belt cleaner occasionally to refresh the sandpaper
Safety
This sander features overload detection. If the machine detects too high a load, it will automatically slow down the feed. This saves wear and tear on the machine, but may cause burning of the workpiece if you cut too aggressively.
- The height adjustment on this machine is VERY aggressive. A full turn will raise the table by more than 2mm (a typical cut should be < .5mm). PLEASE USE A MAXIMUM OF 1/8 TURN OF THE HEIGHT WHEEL PER PASS!
- Make your first cuts with a very slow speed (10 or less). Once you are sure the load is OK you can gradually increase the speed on subsequent passes.
- When overload detection kicks in, a red light next to the speed control will turn on. IF YOU SEE THIS LIGHT, PLEASE REDUCE YOUR DEPTH OF CUT AND/OR FEED RATE!
- Like all of our other sanders, sleeves must be above the elbow, and no gloves should be worn. It's pretty easy to get pulled into the rollers.