133
edits
Changes
Jump to navigation
Jump to search
Line 4:
Line 4: − + Line 16:
Line 16: − + Line 39:
Line 39: + + Line 49:
Line 51: − − === Maintenance === − [https://wiki.pumpingstationone.org/Universal_Maintenance Universal Maintenance] Line 70:
Line 69: + + Line 75:
Line 76: − + − + − + + − + Line 133:
Line 135: + + + + + + + + Line 140:
Line 150: + + + + + + + + Line 156:
Line 174: + + + + Line 214:
Line 236: + + + + + + + + + + + + + + + + +
Universal PLS6.150D 150W Laser Engraver (view source)
Revision as of 17:30, 11 February 2020
, 17:30, 11 February 2020no edit summary
| serial=PLS6150DXX082911106339
| serial=PLS6150DXX082911106339
| arrived= August 2017
| arrived= August 2017
| doesitwork=no
| doesitwork=yes
| contact=[[CNC|Lasers Area Host]]
| contact=[[CNC|Lasers Area Host]]
| where=CNC Shop
| where=CNC Shop
== Status ==
== Status ==
* 6/27/2019 Universal was repaired by Scientific Spectrum Midwest to full functionality. Need to fix air supply before the Universal is put back into service. See required parts needed [[Media:Air_Assist_Parts_Assembly.doc ]] See [[Media:2_Table_Calibration_Platform_Lasers.pdf]] and [[Media:5_Cleaning_and_Maintenance.pdf]] for maintenance. If you need to get familiar with the universal, please checkout out [[Media:6_Keep_these_thoughts_in_mind_when_creating_a_drawing.pdf]] and [[Media:7 Laser procedure.pdf]]
* 5/19/2019 Universal laser is not working. Ask the Area Host at [email protected] for more information.
* 5/19/2019 Universal laser is not working. Ask the Area Host at [email protected] for more information.
* 04/1/2019 Back Up And running, Check Google Group for more details
* 04/1/2019 Back Up And running, Check Google Group for more details
* [[Media:Universal PLS6.150D user guide.pdf|Universal Laser PLS6.150D User Manual]]
* [[Media:Universal PLS6.150D user guide.pdf|Universal Laser PLS6.150D User Manual]]
* [https://docs.google.com/spreadsheets/d/11G3HMFiu8aKGAu2Eg_p9LCSjKiajoUDsriVcqi_09hU/pub?output=html#| Materials Settings Reference]
* [https://docs.google.com/spreadsheets/d/11G3HMFiu8aKGAu2Eg_p9LCSjKiajoUDsriVcqi_09hU/pub?output=html#| Materials Settings Reference]
* [[Media:6_Keep_these_thoughts_in_mind_when_creating_a_drawing.pdf]]
* [[Media:7 Laser procedure.pdf]]
== About ==
== About ==
== Procedures ==
== Procedures ==
=== Setting Up Your Computer===
=== Setting Up Your Computer===
=== Exhaust ===
=== Exhaust ===
* Turn on the Exhaust Fan by flipping the switch on the gray box to the left of the Boss Laser.
* Turn on the Exhaust Fan by flipping the switch on the gray box to the left of the Boss Laser.
* Make sure the BLAST GATE is open.
* It is always good practice to open the Make-up Air Window to allow fresh air to circulate while running a job.
=== Powering On Machine ===
=== Powering On Machine ===
== Running your job ==
== Running your job ==
*Use the printer driver and Universal Control Panel (UCP) to send data to the laser.
* Use the printer driver and Universal Control Panel (UCP) to send data to the laser.
*The printer driver is discussed from page 39-57 of the manual, and on page 58-62, the UCP is explained.
* The printer driver is discussed from page 39-57 of the manual, and on page 58-62, the UCP is explained.
*https://wiki.pumpingstationone.org/images/Universal_PLS6.150D_user_guide.pdf
* https://wiki.pumpingstationone.org/images/Universal_PLS6.150D_user_guide.pdf
* ALLOW AT LEAST 30 SECONDS TO ELAPSE BEFORE LIFTING THE LID AFTER A JOB.
=== Powering Off Machine ===
=== Powering Off Machine ===
* Allow the Exhaust & Air Assist to run for approximately 10-15 after completing a job. (DO NOT CYCLE THE EXHAUST SYSTEM RAPIDLY).
* Allow the Exhaust & Air Assist to run for approximately 10-15 min. after completing a job. (DO NOT CYCLE THE EXHAUST SYSTEM RAPIDLY).
* Turn off the Exhaust & Air Assist FIRST
* Turn off the Exhaust & Air Assist FIRST
* Power down the machine
* Power down the machine
|}
|}
== Maintenance ==
Please note that ONLY authorized maintainers are allowed to perform regular maintenance.
[https://wiki.pumpingstationone.org/Universal_Maintenance Universal Maintenance]
* [[Media:2_Table_Calibration_Platform_Lasers.pdf]]
* [[Media:5_Cleaning_and_Maintenance.pdf]]
== List of Currently Authorized Users ==
== List of Currently Authorized Users ==
! Trained By
! Trained By
! Date
! Date
|-
|[[user:mvictoras|Victor Mateevitsi]]
|Deanna Musurlian
|9/21/2019
|-
|Nikolas Gamarra
|Deanna Musurlian
|9/21/2019
|-
|-
|Fritz Sullivan
|Fritz Sullivan
|Ashish Jasani
|Ashish Jasani
|
|
|-
|Anna Yu
|Ashish Jasani
|12/19/2017
|-
|-
|Revant Ohri
|Revant Ohri
|2018-08-2
|2018-08-2
|-
|-
|-
|[[Nathan Upchurch]]
|Deanna Williams
|2019-08-13
|-
|}
== List of Currently Authorized Maintainers ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
! Date
|-
|[Maintainer]
|Trained by...
|Date trained...