Wood Shop Dust Collection

Sponsor

Matt Triano (Officially)

History

• 2014-05-xx - Discussion open on member list
• 2014-xx-xx - Announced
• 2014-xx-xx - Vote

Background

The proposal is to buy a cyclone style wood dust collection system that can bring the dust down to a safe level. The current system (Jet collector on the table saw, shop vacuums on the small machines) catches only the large particles and distribute the smallest, most dangerous, particles through the shop. Some of the woodworking tools, e.g. drill press & bandsaw, have no provisions for dust collection.

Health Hazards of Wood Dust

Exposure to wood dust has long been associated with a variety of adverse health effects, including dermatitis, allergic respiratory effects, mucosal and nonallergic respiratory effects, and cancer. Contact with the irritant compounds in wood sap can cause dermatitis and other allergic reactions. The respiratory effects of wood dust exposure include asthma, hypersensitivity pneumonitis, and chronic bronchitis.

Do we produce enough dust for it to be a problem?

Based on the following, approximately 35% of airborne dust (by weight) generated by cutting oak is in the 1 to 10 micron range. http://en.wikipedia.org/wiki/File:Particle_size_distribution_of_hardwood_dust.jpg

10% of dust (by volume) generated by sawing oak consists of particles smaller than 15.1 microns. http://annhyg.oxfordjournals.org/content/44/6/455.full.pdf Approximately 1/3 of this is < 10 micron.

Particle Monitoring

The most hazardous dust particles are too small to be seen (<10 microns). To determine the effectiveness of the collection system, we will use a relatively inexpensive laser particle counter, such as: http://www.dylosproducts.com/dcproairqumo.html This will help us fine tune the collection system and tell us when there is insufficient flow due to duct blockage, excessive open gates, or dirty filters.

Goals

• Achieve better air quality inside the shop than outside.

• Meet ACGIH air flow recommendations for each woodworking machine (400-1000 CFM). http://billpentz.com/woodworking/Cyclone/dc_basics.cfm#CFMRequirementsTable

• 4000 FPM air flow in ducting.

• Meet American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Value (TLV) of 1 mg/m**3 Time Weighted Average (TWA).

Dust Collector

http://www.clearvuecyclones.com/cv-max/13-cv-max-three-phase-with-filters.html

Collector dimensions are approximately 24" x 52" x 96" tall.

5 HP motor (Leeson 132242.00, frame 184TC, 86.5% efficiency, 12 f.l. amps, 230v. 3 phase)

This dust collector will have sufficient flow with two open gates. Occasional use with three gates open is acceptable. The 'nano' filter option ($100) is recommended (Efficiency: 99.999% at .5 micron) Collector cost with nano filter is $2070.

Clearvue technical support does not recommend mixing wood and metal dust in the same collection system.

Ducting

6" PVC sewer & drain pipe for drops

8" PVC sewer & drain pipe for main lines

Down Drops

Each large machine or cluster of small machines will require a down drop from the main duct to the machine port or manifold. The drop will require:

• 8x8x6 DWV PVC Wye fitting (the last drop on the main could use a 8"45 & 8" to 6" reducer instead of a wye. this would probably be cheaper the wye plus a cap.)
• 6" 45 elbow
• approximately 5' of 6" PVC pipe
• 6" blast gate
• short length of 6" flexible hose (length dependent on machine).
• switch (wireless or wired) to control the collector motor near the blast gate.

down drops:

• SawStop table saw
• ShopBot CNC router
• Delta 14" bandsaw, router table
• jointer, drill press
• planer, sanders, miter saw

Automating this stuff

Initially, the dust collector will be turned on and off manually and the blast gates will be opened manually. After all the wood working machines are connected to the dust collector, we will work to automate the gates and collector motor - turning on a tool will activate the collector.

Wood Working Machine Collection Strategies

• ShopBot Router - A dust skirt with port is included with the machine. We will need to provide a flexible hose and support. Probably a transition from 6" down to the skirt port. Size of the port is unknown at this point.
• SawStop Table saw = Initially use 6" drop to a 6" to 4" tapered transition connected directly to the stock cabinet port. 3" duct to the blade guard. Consider this blade guard: http://www.thesharkguard.com/ Monitor result and increase the cabinet port size to 6" if required. Useful discussion on dust collection for the sawstop: http://lumberjocks.com/topics/33892
• Jointer = currently has a port approximately 4" in diameter. It appears that we an install a 6" port without difficulty and with no permanent changes to the jointer.
• Mitre saw = this tool throws a lot of dust at high speed and is one of the more difficult tools to collect dust effectively. Definitely needs a shroud.
• Delta 14" Bandsaw = Add a 4" port to a new lower wheel cover (make out of wood?) This is Ed's saw and we don't want to permanently modify the existing cover). http://www.highlandwoodworking.com/bandsaw-dust-control-that-works-2.aspx
• Belt/disk sander (probably needs a shroud for the belt, or just a better sander)
• Planer (could probably use side shrouds)
• Drill press

Collector Location

The dust collector will be either centrally located in the wood working area ( to minimize duct lengths) or at the back of the shop to keep it out of the way and minimize the effects of the noise. The main duct will be run overhead, most likely lying on the bottom member of the ceiling trusses.

Budget

Spreadsheet: https://docs.google.com/spreadsheets/d/1DEpszf0J_o_FLTqVH8XopYjlOpG-GloZYVA1FlCf_E8/edit?usp=sharing

Clearvue CVMAX 3 phase with nano filters $2070, shipping $180

Filter clean out box $80

round fiber drum $50

Dylos DC1100-PRO-PC air quality monitor $290

For each down drop (5 total):

• 8x8x6 45 DWV PVC wye $44.76 https://www.plumbersstock.com/product/10258/8inx8inx6in-pvc-sdr35-wye/ (verify this supplier before relying on it.) alternative: $83 each http://www.nibco.com/Fittings/Plastic-Fittings/PVC-DWV-Fittings/4810-45-Wye-H-x-H-x-H-PVC-DWV/

• 6" 45 DWV PVC elbow $8 each http://www.lowes.com/pd_1824-676-6P03_4294765362__?productId=3452924&Ns=p_product_qty_sales_dollar%7C1&pl=1&currentURL=%3FNs%3Dp_product_qty_sales_dollar%7C1&facetInfo=

• 5' 6" DWV PVC pipe $11.50 each http://www.lowes.com/pd_86806-1814-PVC+04600++0600_0__?productId=3135431&Ntt=dwv+pvc+pipe&pl=1&currentURL=%3FNtt%3Ddwv%2Bpvc%2Bpipe&facetInfo=

• 6" blast gate $15 each http://www.clearvuecyclones.com/supporting-products/38-blast-gate-6.html

• 3' 6" flexible tubing. $20 each

Shark Guard blade guard for SawStop $173

7 pieces of 8"x10' DWV PVC solid core pipe http://www.menards.com/main/plumbing/rough-plumbing/pipe-tubing-fittings/pipe/pvc-pipes/schedule-40-solid-core-pipe-8x10/p-2177274-c-8571.htm

6" flexible PVC hose 25' $92 http://wynnenv.com/products-page/woodworking_hose/pvc-hose/

miscellaneous mounting hardware (all thread rod, beam clamps, hose clamps) $20

Caulk (for PVC pipe) $50

electrical (wire, conduit, circuit breaker, switches, relay) $150

4" ports 6" ports

10% will be added for unanticipated expenses.

5% discount from Clearvue

$600 allocated for dust collection from the Shopbot vote.

Total $4004 Operating cost estimate:

3.24kw X .12$/kwh = $.39/hour

(filters last indefinitely with regular maintenance)

Installation

The installation of the dust collection system will be done by PS1 volunteers. We will target the machines that produce the most dust first (likely the CNC router and table saw). Many of our woodworking machines have inadequate provisions for dust collection and will require custom shrouds and some tinkering to make them effective. This work may take longer than 90 days to complete for all the machines. Because of this, the spending authorization for the ducting and accessories will be extended.

The PVC joints will be sealed with silicone caulk rather than glued, to allow for reuse of the pipe and fittings if we have a layout change.

For planning purposes: the current woodshop is approximately 34' x 21'. Ceiling is 14'.

Electrical Requirements

3 phase 230v, 12 amps. The collector motor will be switched through a relay controlled by a low voltage switches near each blast gate.

Dust Collection Links

http://billpentz.com/woodworking/Cyclone/index.cfm

http://sandwichtechskis.com/ski-builders-shop.htm

Overview of wood dust and collection:

http://www.fwwa.org.au/Art005_WoodDust_c1.pdf

Language

Authorize the board to spend up to $4004 on a dust collection system. Authorization for the dust collector expires in 90 days. Authorization for the related equipment (ducting, hardware, ports, etc) expires in 180 days.