297
edits
Changes
From Pumping Station One
UniFi Security Gateway Pro (view source)
Revision as of 22:26, 1 January 2018
, 22:26, 1 January 2018no edit summary
|serial = SERIAL NUMBER
|serial = SERIAL NUMBER
|arrived = 12/2017
|arrived = 12/2017
|where = Server Rack
|where = [[Dell PS 38S Server Rack]]
|doesitwork = yes
|doesitwork = yes
|contact = CTO
|contact = CTO
== Status ==
== Status ==
Online as of 12/30/17
Device will be moved to the new infrastructure location with other PS:1 maintained equipment.
== Backup ==
Configuration is backed up with the [[UniFi Controller]].
== Configuration ==
Please see [[UniFi Controller]] for extended configuration information. USG is managed from controller interface.
Port configuration is as follows:
* LAN Port 1
** Connected to [[UniFi 48 Port Switch]] on port 32, will be switched to port 1 or 48.
* LAN Port 2
** Disconnected. May be used in the future to service member rack.
* WAN Port 1
** Connected to primary internet connection, currently the Motorola SURFboard SB6120 on top of the [[Dell PS 38S Server Rack]]
* WAN Port 2
** Disconnected. Will be used in the future for a failover/backup internet connection.
== Enable IPv6 Support ==
IPv6 support is in progress. [https://help.ubnt.com/hc/en-us/articles/115005868927-UniFi-How-to-Implement-IPv6-with-DHCPv6-and-Prefix-Delegation-on-USG Documentation to enable this is found here.]
== Initial Setup ==
[https://help.ubnt.com/hc/en-us/articles/236281367-UniFi-How-to-Adopt-a-USG-into-an-Existing-Network Instructions for adpoting a USG Pro can be found here]
=== Adpoting a USG Pro into an existing network ===
NOTE: This has been tailored for PS:1's existing network setup.
1. Connect a computer into the LAN NIC (LAN port 1) of the USG. It will obtain a 192.168.1.x IP from DHCP.
2. SSH into 192.168.1.1 using username and password combination of ubnt / ubnt.
3. For this example, the controller is on 10.100.0.9/20, so let's change the USG’s LAN IP to 10.100.0.1. Choose an available IP within the subnet of the local controller.
4. In the SSH session, run the following (Since this is a USG Pro, eth1 has been replaced with eth0 per Ubiquiti instructions):
* configure
* set interfaces ethernet eth0 address 10.100.0.1/20
* delete interfaces ethernet eth0 address 192.168.1.1/24
* commit
Now the USG’s LAN IP is 10.100.0.1/20. The SSH session will drop.
=== Controller Configuration ===
In order for the USG to work properly, you must correctly configure the appropriate settings in the UniFi Controller GUI located at https://10.0.0.9:8443 or via https://unifi.ubnt.com/
Under "Settings" > "Networks", select edit on the network named "LAN".
The following settings should be configured as such:
* Name
** LAN
* Purpose
** Corporate
* Parent Interface
** LAN
*Gateway/Subnet
** 10.100.0.1/20
* Domain Name
** ad.pumpingstationone.org
* IGMP SNooping
** Disabled
* DHCP Mode
** DHCP Server
* DHCP Range
** 10.100.3.1 - 10.100.14.254
* DHCP Name Server (EACH IP IS A SEPERATE FIELD)
** Manual
*** 10.100.0.132, 10.100.0.105, 10.100.0.1, 8.8.8.8
*DHCP WINS Server
** Disabled
* DHCP Lease Time
** 86400 seconds
* DHCP Gateway IP
** Auto
* DHCP UniFi Controller
** 10.100.0.9
* DHCP Gaurding
** Enabled
*** 10.100.0.1
* UPnP LAN
** Disabled
ADVANCED SETTINGS:
* DHCP NTP Server
** Disabled
* DHCP Network Boot
** Enabled
*** 10.100.0.110
*** /pxelinux.0
* DHCP Time Offset
** Disabled
* DHCP WPAD URL
** Empty
* DHCP TFTP Server
** Empty
[[Category:IT Equipment]]
[[Category:Systems]]
