Line 7: |
Line 7: |
| |serial = SERIAL NUMBER | | |serial = SERIAL NUMBER |
| |arrived = 12/2017 | | |arrived = 12/2017 |
− | |where = Server Rack | + | |where = [[Dell PS 38S Server Rack]] |
| |doesitwork = yes | | |doesitwork = yes |
| |contact = CTO | | |contact = CTO |
Line 16: |
Line 16: |
| == Status == | | == Status == |
| | | |
− | To be filled
| + | Online as of 12/30/17 |
| + | |
| + | Device will be moved to the new infrastructure location with other PS:1 maintained equipment. |
| + | |
| + | == Backup == |
| + | |
| + | Configuration is backed up with the [[UniFi Controller]]. |
| + | |
| + | == Configuration == |
| + | |
| + | Please see [[UniFi Controller]] for extended configuration information. USG is managed from controller interface. |
| + | |
| + | Port configuration is as follows: |
| + | |
| + | * LAN Port 1 |
| + | ** Connected to [[UniFi 48 Port Switch]] on port 32, will be switched to port 1 or 48. |
| + | * LAN Port 2 |
| + | ** Disconnected. May be used in the future to service member rack. |
| + | |
| + | * WAN Port 1 |
| + | ** Connected to primary internet connection, currently the Motorola SURFboard SB6120 on top of the [[Dell PS 38S Server Rack]] |
| + | * WAN Port 2 |
| + | ** Disconnected. Will be used in the future for a failover/backup internet connection. |
| + | |
| + | == Enable IPv6 Support == |
| + | |
| + | IPv6 support is in progress. [https://help.ubnt.com/hc/en-us/articles/115005868927-UniFi-How-to-Implement-IPv6-with-DHCPv6-and-Prefix-Delegation-on-USG Documentation to enable this is found here.] |
| + | |
| + | == Initial Setup == |
| + | |
| + | [https://help.ubnt.com/hc/en-us/articles/236281367-UniFi-How-to-Adopt-a-USG-into-an-Existing-Network Instructions for adpoting a USG Pro can be found here] |
| + | |
| + | === Adpoting a USG Pro into an existing network === |
| + | |
| + | NOTE: This has been tailored for PS:1's existing network setup. |
| + | |
| + | 1. Connect a computer into the LAN NIC (LAN port 1) of the USG. It will obtain a 192.168.1.x IP from DHCP. |
| + | |
| + | 2. SSH into 192.168.1.1 using username and password combination of ubnt / ubnt. |
| + | |
| + | 3. For this example, the controller is on 10.100.0.9/20, so let's change the USG’s LAN IP to 10.100.0.1. Choose an available IP within the subnet of the local controller. |
| + | |
| + | 4. In the SSH session, run the following (Since this is a USG Pro, eth1 has been replaced with eth0 per Ubiquiti instructions): |
| + | |
| + | * configure |
| + | * set interfaces ethernet eth0 address 10.100.0.1/20 |
| + | * delete interfaces ethernet eth0 address 192.168.1.1/24 |
| + | * commit |
| + | |
| + | Now the USG’s LAN IP is 10.100.0.1/20. The SSH session will drop. |
| + | |
| + | === Controller Configuration === |
| + | |
| + | In order for the USG to work properly, you must correctly configure the appropriate settings in the UniFi Controller GUI located at https://10.0.0.9:8443 or via https://unifi.ubnt.com/ |
| + | |
| + | Under "Settings" > "Networks", select edit on the network named "LAN". |
| + | |
| + | The following settings should be configured as such: |
| + | |
| + | * Name |
| + | ** LAN |
| + | * Purpose |
| + | ** Corporate |
| + | * Parent Interface |
| + | ** LAN |
| + | *Gateway/Subnet |
| + | ** 10.100.0.1/20 |
| + | * Domain Name |
| + | ** ad.pumpingstationone.org |
| + | * IGMP SNooping |
| + | ** Disabled |
| + | * DHCP Mode |
| + | ** DHCP Server |
| + | * DHCP Range |
| + | ** 10.100.3.1 - 10.100.14.254 |
| + | * DHCP Name Server (EACH IP IS A SEPERATE FIELD) |
| + | ** Manual |
| + | *** 10.100.0.132, 10.100.0.105, 10.100.0.1, 8.8.8.8 |
| + | *DHCP WINS Server |
| + | ** Disabled |
| + | * DHCP Lease Time |
| + | ** 86400 seconds |
| + | * DHCP Gateway IP |
| + | ** Auto |
| + | * DHCP UniFi Controller |
| + | ** 10.100.0.9 |
| + | * DHCP Gaurding |
| + | ** Enabled |
| + | *** 10.100.0.1 |
| + | * UPnP LAN |
| + | ** Disabled |
| + | |
| + | ADVANCED SETTINGS: |
| + | |
| + | * DHCP NTP Server |
| + | ** Disabled |
| + | * DHCP Network Boot |
| + | ** Enabled |
| + | *** 10.100.0.110 |
| + | *** /pxelinux.0 |
| + | * DHCP Time Offset |
| + | ** Disabled |
| + | * DHCP WPAD URL |
| + | ** Empty |
| + | * DHCP TFTP Server |
| + | ** Empty |
| + | |
| + | [[Category:IT Equipment]] |
| + | [[Category:Systems]] |