Difference between revisions of "Screen Printing Workshop first test"
Jump to navigation
Jump to search
m (New page: == Intro == On February 18, 2009 I made my first attempt at creating a screen using Diazo photo emulsion from Speedball. Details to follow. --Nathan == Preparation ==...) |
m (Updates) |
||
Line 28: | Line 28: | ||
* I burned the screen for 15 minutes, checked it, uneducated guess is that it needs more time to expose. Check again in 15 more minutes. (10:34 PM) | * I burned the screen for 15 minutes, checked it, uneducated guess is that it needs more time to expose. Check again in 15 more minutes. (10:34 PM) | ||
** Now is a good time to note that I should have attached my positive to the screen so when I checked it the alignment wouldn't get messed up. | ** Now is a good time to note that I should have attached my positive to the screen so when I checked it the alignment wouldn't get messed up. | ||
+ | * I decided to let it stay for another 30 that way if it overexposed I would have a high point of reference. From what little experience I have it doesn't seem to have changed much. The emulsion basically just gets ''slightly'' more transparent. | ||
+ | * After 45 minutes I pulled the screen off the light and washed out the print areas with my high pressure spray nozzle. It takes a minute or two for the areas to start clearing out (I was worried) but then slowly they will empty out. | ||
+ | * Letting screen dry completely will I prepare my kitchen table for test prints. | ||
== Result == | == Result == |
Revision as of 05:29, 19 February 2009
Intro
On February 18, 2009 I made my first attempt at creating a screen using Diazo photo emulsion from Speedball. Details to follow. --Nathan
Preparation
Materials:
- Lightbox (with 6 20 watt daylight fluorescent bulbs, distance from screen: ~7"
- 12"x10" Dick Blick screen #94708 (upc:651032 947087)
- Speedball Diazo photo emulsion kit
- Speedball 10" squeegee
- NOTE: It would have been good to invest in a scoop coater as well
- Flat, heavy materials. I went with Flash MX Bible, Visual Basic 6 Black Book, SAMS Visual C++ 6, SAMS Teach Yourself LAMP & Basic Electronics text book.
- Clothes you're not worried about ruining
- Patience
Application
- Diazo photo emulsion kit requires mixing sensitizer (Black) into the base emulsion (Blue) to activate. Do so and mix vigorously (Resulting mixture turns green.)
- Directions state emulsion can last for up to 4 months when stored in refrigerator.
- Carefully applied emulsion to both sides of screen with Speedball squeegee. This is where I could have made less mess with a scoop coater.
- After checking that both sides were coated as evenly as possible I IMMEDIATELY took the screen to dry in a dark arrid place. In my case I used my oven (no heat necessary). According to instructions, dry the screen with the flat side down, but elevated.
- screen appeared to be perfectly dry in 1 hour, could have gone with 45 minutes probably.
- Do not expose screen to light until you are ready for printing. This is why I need to build a drying box.
Exposure
- I burned the screen for 15 minutes, checked it, uneducated guess is that it needs more time to expose. Check again in 15 more minutes. (10:34 PM)
- Now is a good time to note that I should have attached my positive to the screen so when I checked it the alignment wouldn't get messed up.
- I decided to let it stay for another 30 that way if it overexposed I would have a high point of reference. From what little experience I have it doesn't seem to have changed much. The emulsion basically just gets slightly more transparent.
- After 45 minutes I pulled the screen off the light and washed out the print areas with my high pressure spray nozzle. It takes a minute or two for the areas to start clearing out (I was worried) but then slowly they will empty out.
- Letting screen dry completely will I prepare my kitchen table for test prints.