Line 16: |
Line 16: |
| |itemphoto = | | |itemphoto = |
| }} | | }} |
− | '''This tool requires authorization for use.''' | + | '''This tool requires certification for use.''' |
− | ==Authorization is by authorized proctors only== | + | == Personal Protective Equipment == |
− | ==PERSONAL PROTECTIVE EQUIPMENT==
| |
| | | |
| * Face shield or safety glasses must be worn. | | * Face shield or safety glasses must be worn. |
Line 24: |
Line 23: |
| * Do not wear gloves or loose clothing. | | * Do not wear gloves or loose clothing. |
| * Remove watches,rings,and other jewelry. | | * Remove watches,rings,and other jewelry. |
− | * Don't wear long sleeves or roll them up. | + | * Don't wear or roll up long sleeves. |
| * Hearing protection may be required. | | * Hearing protection may be required. |
| * Dust protection may be required. | | * Dust protection may be required. |
| | | |
− | ==PRE-OPERATIONAL SAFETY CHECKS== | + | == Pre-Operational Safety Checks == |
| *Locate and ensure you are familiar with all machine operations and controls. | | *Locate and ensure you are familiar with all machine operations and controls. |
| *Ensure all guards are fitted, secure and functional. Do not operate if guards are missing or faulty. | | *Ensure all guards are fitted, secure and functional. Do not operate if guards are missing or faulty. |
Line 38: |
Line 37: |
| *Make sure all clamping handles are tight, | | *Make sure all clamping handles are tight, |
| | | |
− | ==OPERATIONAL SAFETY CHECKS== | + | == Operational Safety Checks == |
| *Before making adjustments, switch off and bring the machine to a complete standstill. | | *Before making adjustments, switch off and bring the machine to a complete standstill. |
| *Keep the tool rest adjusted close to the work and at the correct height. | | *Keep the tool rest adjusted close to the work and at the correct height. |
Line 44: |
Line 43: |
| *Stop the lathe and remove all tool rests before sanding. | | *Stop the lathe and remove all tool rests before sanding. |
| | | |
− | ==ENDING OPERATIONS AND CLEANING UP== | + | == Ending Operations and Cleaning Up == |
| *Switch off the machine when work completed. | | *Switch off the machine when work completed. |
| *Return all chisels and other tools to racks. | | *Return all chisels and other tools to racks. |
| *Leave the machine in a safe, clean and tidy state. | | *Leave the machine in a safe, clean and tidy state. |
| | | |
− | ==POTENTIAL HAZARDS AND INJURIES== | + | == Potentional Hazards and Injuries == |
| *Eye injuries from flying debris or defective timber. | | *Eye injuries from flying debris or defective timber. |
| *Hair/clothing getting caught in moving machine parts. | | *Hair/clothing getting caught in moving machine parts. |
| *Airborne dust. | | *Airborne dust. |
| | | |
− | ==DO== | + | == Do == |
| * Rough cut the workpiece as close as possible to the finished shape before installing it. | | * Rough cut the workpiece as close as possible to the finished shape before installing it. |
| * Check your workpiece for flaws, cracks, knots etc.and test glue joints before mounting the workpiece on machine. | | * Check your workpiece for flaws, cracks, knots etc.and test glue joints before mounting the workpiece on machine. |
Line 60: |
Line 59: |
| * Remove the tool rest before sanding or polishing. | | * Remove the tool rest before sanding or polishing. |
| | | |
− | ==DON'T== | + | == Don't == |
| * Drive the workpiece into the drive center while the drive center is in the headstock. | | * Drive the workpiece into the drive center while the drive center is in the headstock. |
| **Set the drive center into the workpiece with a soft mallet prior to installing it on the headstock. | | **Set the drive center into the workpiece with a soft mallet prior to installing it on the headstock. |
| | | |
| | | |
− | == Authorized Proctors == | + | == List of Currently Certified Users == |
| {| class="wikitable" border="1" | | {| class="wikitable" border="1" |
| ! Qualified Member | | ! Qualified Member |
− | ! Authorized By | + | ! Trained By |
| |- | | |- |
− | |Matt Triano
| |
− | |Danger Committee
| |
− | |-
| |
− | |Joeseph Nudell
| |
− | |Danger Committee
| |
− | |-
| |
− | |Jason Shanfield
| |
− | |Danger Committee
| |
− | |-
| |
− | |Michael Skilton
| |
− | |Danger Committee
| |
− | |-
| |
− | |}
| |
− | == Authorized Users==
| |
− | {| class="wikitable" border="1"
| |
− | ! Qualified Member
| |
− | ! Authorized By
| |
| |- | | |- |
| |} | | |} |
| | | |
| ==Documentation== | | ==Documentation== |
− | [[File:708352_man.pdf]]
| |
− |
| |
− | https://wiki.pumpingstationone.org/Wood_Lathe_Authorization_Checklist
| |
| | | |
| [[Category:Woodworking]] | | [[Category:Woodworking]] |
| [[Category:Shop Equipment]] | | [[Category:Shop Equipment]] |