Line 1: |
Line 1: |
| + | |
| + | |
| + | |
| {{Template:EquipmentPage | | {{Template:EquipmentPage |
| |image = boice_crane.jpg | | |image = boice_crane.jpg |
| |owner=PS:One | | |owner=PS:One |
− | |model=Boice Crane Gear Head | + | |model=Boice Crane 24103 24" Power Feed |
| |arrived=January 2015 | | |arrived=January 2015 |
| |serial=23649 | | |serial=23649 |
| |doesitwork=yes | | |doesitwork=yes |
| |contact=Dean Anderson | | |contact=Dean Anderson |
− | |where=Machine Shop | + | |where=Cold Metals |
| |certification=yes | | |certification=yes |
| |hackable=no | | |hackable=no |
| |value=$600}} | | |value=$600}} |
| | | |
| + | =Removal Section= |
| + | *What is it? - Boice Crane Drill Press |
| + | *Who is sponsoring? - Cold Metals Host - Jim Brink |
| + | *Date published to the mailing list and RT- 06/11/2018 |
| + | *Asset value - $100 |
| + | *Suggested method of removal - Public sale- Craigslist |
| + | *Background notes - |
| + | *Resolution of removal - |
| + | *Approval - |
| | | |
| == Specifications == | | == Specifications == |
| 8 speed | | 8 speed |
− | Gear-head. No belts to slip, which means there is a lot of torque. | + | |
− | #3 Morse taper spindle | + | Gear-head. No belts or Jacobs chuck to slip, which means there is a lot of torque. |
| + | |
| + | Morse #3 taper spindle |
| + | |
| Capacity, cast iron 1 1/4" | | Capacity, cast iron 1 1/4" |
| + | |
| Drills to center 23" | | Drills to center 23" |
| + | |
| approximate weight 600 pounds | | approximate weight 600 pounds |
| + | |
| motor HP 1.5 (high) 1.2 (low) | | motor HP 1.5 (high) 1.2 (low) |
| + | |
| Spindle speeds (8) 84, ... | | Spindle speeds (8) 84, ... |
| | | |
Line 31: |
Line 50: |
| Work piece needs secure mounting due to spindle's high torque | | Work piece needs secure mounting due to spindle's high torque |
| | | |
− | No through hole (table designed for coolant), must use vise or spoil layer | + | No through hole (table designed for coolant), must use vise |
| | | |
| No quill stop, must set table or head height to prevent drilling into table | | No quill stop, must set table or head height to prevent drilling into table |
Line 43: |
Line 62: |
| Drill shanks must be firmly seated in taper | | Drill shanks must be firmly seated in taper |
| | | |
− | To remove drill, align slots in spindle, insert wedge, grasp drill, tap wedge with hammer | + | To remove drill, lower spindle to expose the slot in the quill, turn the spindle by hand until the quill slot lines up with the spindle slot, insert the #3 drift into the slot with the curved edge facing up, grasp drill, tap drift with hammer |
| | | |
| == To-Do == | | == To-Do == |
Line 60: |
Line 79: |
| | | |
| == Maintenance == | | == Maintenance == |
| + | [[Boice_Crane_Drill_Press_maintenance|Boice_Crane_Drill_Press_maintenance]] |
| | | |
| == Equipment == | | == Equipment == |
Line 85: |
Line 105: |
| | Dean Anderson | | | Dean Anderson |
| |9/15/2015 | | |9/15/2015 |
| + | | |
| + | |- |
| + | |Greg Kudlacz |
| + | |Todd Allen |
| + | |- |
| + | |
| + | |Dafe Hughes |
| + | |Todd Allen |
| + | |- |
| + | |Connor Sullivan |
| + | |Tom Judge |
| + | |1/22/16 |
| + | |- |
| + | |Abel Greenwald |
| + | |Michael Patton |
| + | |- |
| + | |Bruce Mace |
| + | |Chris Ruhland |
| + | |3/7/17 |
| + | |- |
| + | |Sam Chen |
| + | |Chris Ruhland |
| + | |3/7/17 |
| + | |- |
| + | |Michael Ice |
| + | |Sam Olendorf |
| + | |2/08/18 |
| + | |Aaron Hale |
| + | |Sam Olendorf |
| + | |8/8/2018 |
| |-} | | |-} |
| | | |
− | [[Category:Metalworking]] | + | [[Category:Cold Metals]] |
− | [[Category:Coldmetals]]
| |