3,430
edits
Changes
Jump to navigation
Jump to search
mLine 1:
Line 1: − [[Category:Fabrication]] − Line 42:
Line 40: − + − + − + − + − + − + Line 63:
Line 61: − + − + − + Line 91:
Line 89: − + − + Line 146:
Line 144: + +
Robot: Cosmetic changes
{{Template:EquipmentPage
{{Template:EquipmentPage
|owner = ?
|owner = ?
*** Hearing Protection is optional but recommended
*** Hearing Protection is optional but recommended
*** Mask should be worn when cutting dusty materials (MDF, Composites)
*** Mask should be worn when cutting dusty materials (MDF, Composites)
*** Vacuum. Hold a vacuum right up to the cutting area when using dusty or dangerous things (fiberglass, composities, MDF)
*** Vacuum. Hold a vacuum right up to the cutting area when using dusty or dangerous things (fiberglass, composities, MDF)
*** Bits are razor sharp so be careful handling or installing them. Most of the injuries I see are when the machine is off. #1 is bumping you hand into the bit in the spindle when setting up your work.
*** Bits are razor sharp so be careful handling or installing them. Most of the injuries I see are when the machine is off. #1 is bumping you hand into the bit in the spindle when setting up your work.
*** Pinch Points all over the place that can crush fingers.
*** Pinch Points all over the place that can crush fingers.
* What Can Go Wrong
* What Can Go Wrong
** Piece of material stuck on bit. If a piece of material breaks loose and gets caught on the bit turn off the machine and get away. The bit could snap and the material plus sharp bit could fly off.
** Piece of material stuck on bit. If a piece of material breaks loose and gets caught on the bit turn off the machine and get away. The bit could snap and the material plus sharp bit could fly off.
** Bit can break
** Bit can break
** Crash into clamps - damage spindle
** Crash into clamps - damage spindle
*** It happened before...they are not too expensive.
*** It happened before...they are not too expensive.
** Overheating Material - Smoldering embers can start a fire. Some super cheap plywoods and strand board have glues that cause this to happen
** Overheating Material - Smoldering embers can start a fire. Some super cheap plywoods and strand board have glues that cause this to happen
* Learn about Machine
* Learn about Machine
** Power On (don't worry about limits button)
** Power On (don't worry about limits button)
** Turning on Spindle - It now works via Mach3 control!
** Turning on Spindle - It now works via Mach3 control!
** End Stops - I don't know how reliable they are. I don't suggest using them.
** End Stops - I don't know how reliable they are. I don't suggest using them.
** E-Stop (kills power to drivers and spindle, but Mach3 does not know)
** E-Stop (kills power to drivers and spindle, but Mach3 does not know)
** Sacrificial Surface on top of bed - allows you to cut things out without damaging the bed.
** Sacrificial Surface on top of bed - allows you to cut things out without damaging the bed.
** Use profile (icon) on desktop called "Use This One" (MIB_CNC)
** Use profile (icon) on desktop called "Use This One" (MIB_CNC)
** Ignore start up error
** Ignore start up error
** Resetting. It starts in e-stop (reset) mode. Click reset to clear that
** Resetting. It starts in e-stop (reset) mode. Click reset to clear that
** Jogging - Slow and Fast Arrow for X,Y and pgup/pgdown for Z. Shift for fast jog.
** Jogging - Slow and Fast Arrow for X,Y and pgup/pgdown for Z. Shift for fast jog.
** Zeroing. Click buttons next to DROs to zero.
** Zeroing. Click buttons next to DROs to zero.
** Does not matter if you "save the fixture" when you quit
** Does not matter if you "save the fixture" when you quit
** Show the rotary attachment under the table
** Show the rotary attachment under the table
** Regen Toolpath (after jogging)
** Regen Toolpath (after jogging)
** Checking clamps
** Checking clamps
** Feedrate offset. This can be used to slow down a job. Use might want to start below 100% to verify the machine can handle the feedrate you chose.
** Feedrate offset. This can be used to slow down a job. Use might want to start below 100% to verify the machine can handle the feedrate you chose.
* Running Job
* Running Job
** Make sure spindle is on. Mach3 will turn it on, but it is best to do it manually (via Mach 3 button) to verify the speed.
** Make sure spindle is on. Mach3 will turn it on, but it is best to do it manually (via Mach 3 button) to verify the speed.
** Start
** Start
** Pause (Controlled stop that could move a few inches before stopping)
** Pause (Controlled stop that could move a few inches before stopping)
|Bart Dring
|Bart Dring
|-}
|-}
[[Category:Fabrication]]