3
edits
Changes
Jump to navigation
Jump to search
Line 9:
Line 9: − + − + − + Line 189:
Line 189: + + + + + + + + Line 240:
Line 248: − + − + − + Line 327:
Line 335: − − − '''THERE IS CURRENTLY NO POST PROCESSOR FOR RUNNING WITH THESE CONSUMABLES INSTALLED''' − Line 1,134:
Line 1,138: + − + + + + Line 1,198:
Line 1,206: + + + +
→Procedures: Added, Error: "Probe ignore, activated at call for probe"
|where = Hot metals
|where = Hot metals
|doesitwork = yes
|doesitwork = yes
|contact = CNC Area Host
|contact = hotmetals at pumpingstationone.org
|value = $6000
|value = $6000
|image = IMG_4045.JPG
|image = Cncplasma.jpg
}}
}}
== Status ==
== Status ==
Working. Stay tuned for an announcement about authorizations.
Working.
== Authorization ==
== Authorization ==
* Unknown at this time
* Unknown at this time
==== Error: "Probe ignore, activated at call for probe" ====
'''Tends to happen when attempting to reignite torch after first cut'''
Causes:
*THCv set to high, e.g. cutting 1/4" steel @45A recommended THCv is 115, lower to 114 or until the torch ignites successfully
== Sheet Cam ==
== Sheet Cam ==
* Extend air line to under table to create a manifold for table mounted air consumers
* Extend air line to under table to create a manifold for table mounted air consumers
* Run large conduit for 220 outlet for the plasma cutter
* <s>Run large conduit for 220 outlet for the plasma cutter</s>
* Run small conduit for data/estop between the table and the PC
* Run small conduit for data/estop between the table and the PC
* Run black pipe for connecting the table to the bladder (old compressor tank)
* Run black pipe for connecting the table to the bladder (old compressor tank)
* Water line from north side of the shop, with input into the old compressor tank
* Water line from north side of the shop, with input into the old compressor tank
* Air lines to the compressor tank (one vent on from the compressor)
* <s>Air lines to the compressor tank (one vent on from the compressor)</s>
* Run ethernet line to PC so its not on wifi any more
* <s>Run ethernet line to PC so its not on wifi any more</s> - ''WiFi for network access is fine''
* Z axis limit switches
* Z axis limit switches
=== Fine Cut ===
=== Fine Cut ===
'''NOTE''': These parts are for a t30 unshielded torch, they are compatiable with the T45m when it is run at a setting lower than 30A and cutting materials thinner than 3/16". Ohmic sensing will not work with these parts installed.
'''NOTE''': These parts are for a t30 unshielded torch, they are compatiable with the T45m when it is run at a setting lower than 30A and cutting materials thinner than 3/16". Ohmic sensing will not work with these parts installed.
** Wantai DQ542MA
** Wantai DQ542MA
** Manual: [[File:DQ542MA_English_Manual.pdf]]
** Manual: [[File:DQ542MA_English_Manual.pdf]]
* Ethernet SmoothStepper
* Ethernet SmoothStepper
**https://warp9td.com/index.php/products
**https://warp9td.com/index.php/products
**https://warp9td.com/index.php/documentation/doc-ess
**https://warp9td.com/index.php/documentation/doc-ess
**https://warp9td.com/index.php/gettingstarted/setting-up-the-smoothstepper-and-mach#THC
* C25 Break out board
* C25 Break out board
** https://cnc4pc.com/motion-control/breakout-boards/c25-smooth-stepper-terminal-board.html
** https://cnc4pc.com/motion-control/breakout-boards/c25-smooth-stepper-terminal-board.html
** Manual: [[File:C25R3_1_USER_MANUAL.pdf]]
** Manual: [[File:C25R3_1_USER_MANUAL.pdf]]
*Torch height control
*Torch height control
**Proma Compact THC
**Proma Compact THC
|Ron Olson
|Ron Olson
|01/29/19
|01/29/19
|-
|Greg Bell
|Ron Olson
|03/23/19
|-
|-
|}
|}