Line 1: |
Line 1: |
| {{Template:EquipmentPage | | {{Template:EquipmentPage |
− | |owner=PS:One | + | |owner= PS:One |
− | |model= | + | |model=137 229200 |
| |serial= | | |serial= |
| |arrived= | | |arrived= |
Line 13: |
Line 13: |
| |hostarea=Wood Shop | | |hostarea=Wood Shop |
| }} | | }} |
| + | |
| | | |
| + | The Craftsman 20" drill press is the primary drill press in the wood shop. Authorization is included in the general wood shop authorization. For upcoming authorizations, see the [https://pumpingstationone.org/events/ calendar]. |
| | | |
− | {| class="wikitable" border="1"
| + | == Safety == |
− | ! Qualified Member
| + | Eye protection of course. You only get the one set, take care of them. Drills can grab and spin whatever you're drilling into. Clamp or otherwise support your work. |
− | ! Trained By
| + | |
− | ! Date
| + | The [[:file:Craftsman20_drill_manual.pdf|user manual is available here]]. |
− | |- | + | |
− | |Eric Beauchamp
| + | ==Maintenance== |
− | |Danger committee
| + | Per the [[:file:Craftsman20 drill manual.pdf|user manual]], the drill should be periodically cleaned of dust, the table wiped with wax to prevent rust, and (if needed) the quill lubricated with a dry lubricant like silicone or graphite. Users should perform this maintenance as the drill is used, and PS1 should inspect the drill monthly. |
− | |-
| + | |
− | | [[User:andrewvaughan|Andrew Vaughan]]
| + | ===Maintenance history=== |
− | | Andy Larkin
| + | |
− | | April 26, 2017
| + | * '''July 10, 2017.''' Drill press motor is not fully connected. Belt may be rubbing on the housing. |
− | |-
| + | * '''July 14, 2017.''' One of the two posts that adjusts the motor position is missing its nut. Also, there is a rack-and-pinion lever that moves the motor in and out, and one of the posts had skipped a tooth. I worked it back into position, and I believe it is now safe to use, despite the missing nut. Replacing the nut will require removing the motor, which is a two-person job. |
− | |Paul McClay
| + | * '''July 18, 2017.''' This is fixed now. For the record, the missing nut was M12-1.75. I put some "purple" locktite on both nuts, so hopefully we won't have to take it apart again. |
− | |Ralph Brendler
| |
− | |5/18/17
| |
− | |-
| |
− | |Jim Handley
| |
− | |Ralph Brendler
| |
− | |5/13/17
| |
− | |}
| |
| | | |
| + | == Outside Resources == |
| | | |
− | == Notes == | + | [https://www.youtube.com/watch?v=Gq8jL_ZDjNM| Drill Press Basics] Solid video by <i>Wood Magazine</i>. Highly recommended. |
| | | |
| + | [https://www.engineeringtoolbox.com/drill-bit-speed-hardwood-softwood-d_1451.html| Recommended speeds for the drill press] You'll get much better results if you match the speed to the bit. |
| | | |
− | == Safety == | + | == List of Currently Authorized Users == |
− | user maunal: [[File:Craftsman20_drill_manual.pdf]]
| |
| | | |
− | == List of currently authorized users ==
| + | Authorization for this tool by authorized proctors only. Members not previously Authorized must take the CANVAS course at https://canvas.pumpingstationone.org/courses/40 |
− | {| class="wikitable" border="1"
| |
− | ! Qualified Member
| |
− | ! Trained By
| |
− | ! Auth Date
| |
| |- | | |- |
− | |[[User:spektre1|Danielle MacDonald]]
| |
− | |Ralph Brendler
| |
− | |2017-06-29
| |
| |} | | |} |
− |
| |
− |
| |
| [[Category:Shop Equipment]] | | [[Category:Shop Equipment]] |
| [[Category:Wood Shop]] | | [[Category:Wood Shop]] |