1
edit
Changes
From Pumping Station One
Clarified some rules, formatting
{{Template:EquipmentPage
{{Template:EquipmentPage
|image =
|image =
|owner = Joeseph Nudell
|owner = Joe Nudell
|serial = NAN
|serial = NAN
|certification = yes
|certification = yes
|arrived = 6/1/14
|arrived = 6/1/14
|doesitwork = yes
|doesitwork = yes
|contact = Joeseph Nudell
|contact = Joe Nudell
|where = Woodshop
|where = Woodshop
|value = 800
|value = 800
== Personal Protective Equipment ==
== Personal Protective Equipment ==
* Face shield or safety glasses must be worn.
* Face shield (not just safety glasses) must be worn.
* Long and loose hair must be contained.
* Long and loose hair must be contained.
* Do not wear gloves or loose clothing.
* Do not wear gloves or loose clothing.
* Remove watches,rings,and other jewelry.
* Remove watches, rings, and other jewelry.
* Don't wear or roll up long sleeves.
* Don't wear or roll up long sleeves.
* Dust protection may be required.
* Dust protection may be required.
== Pre-Operational Safety Checks ==
== Pre-Operational Safety Checks ==
*Locate and ensure you are familiar with all machine operations and controls.
* Locate and ensure you are familiar with all machine operations and controls.
*Ensure all guards are fitted, secure and functional. Do not operate if guards are missing or faulty.
* Ensure all guards are fitted, secure and functional. Do not operate if guards are missing or faulty.
*Workpiece must be securely fastened to face plate, chuck or between centers.
* Workpiece must be securely fastened to face plate, chuck or between centers.
* Rotate the workpiece by hand to check clearance between tool rest and bed.
*Rotate the workpiece by hand to check clearance between tool rest and bed.
* Ensure the cutting tools are sharp and in good condition.
*Ensure the cutting tools are sharp and in good condition.
* Start the dust extraction unit before using the machine.
*Start the dust extraction unit before using the machine.
* Make sure all clamping handles are tight.
*Make sure all clamping handles are tight,
== Operational Safety Checks ==
== Operational Safety Checks ==
*Before making adjustments, switch off and bring the machine to a complete standstill.
* Adjust speed to suit the diameter of the work and turning operation (IMPORTANT - *never* adjust speed while the lathe is off!)
*Keep the tool rest adjusted close to the work and at the correct height.
* Before making adjustments (apart from speed), switch off and bring the machine to a complete standstill.
* Keep the tool rest adjusted close to the work and at the correct height.
*Stop the lathe and remove all tool rests before sanding.
* Stop the lathe and remove all tool rests before sanding.
== Ending Operations and Cleaning Up ==
== Ending Operations and Cleaning Up ==
*Switch off the machine when work completed.
* Switch off the machine when work completed.
*Return all chisels and other tools to racks.
* Return all chisels and other tools to racks.
*Leave the machine in a safe, clean and tidy state.
* Leave the machine in a safe, clean and tidy state.
== Potentional Hazards and Injuries ==
== Potential Hazards and Injuries ==
*Eye injuries from flying debris or defective timber.
* Eye injuries from flying debris or defective timber.
*Hair/clothing getting caught in moving machine parts.
* Hair/clothing getting caught in moving machine parts.
*Airborne dust.
* Airborne dust.
== Do ==
== Do ==
* Rough cut the workpiece as close as possible to the finished shape before installing it.
* Rough cut the workpiece as close as possible to the finished shape before installing it.
* Check your workpiece for flaws, cracks, knots etc.and test glue joints before mounting the workpiece on machine.
* Check your workpiece for flaws, cracks, knots etc. and test glue joints before mounting the workpiece on machine.
* Use the lowest speed when starting a new workpiece.
* Use the lowest speed when starting a new workpiece.
* Remove the tool rest before sanding or polishing.
* Remove the tool rest before sanding or polishing.
* Drive the workpiece into the drive center while the drive center is in the headstock.
* Drive the workpiece into the drive center while the drive center is in the headstock.
**Set the drive center into the workpiece with a soft mallet prior to installing it on the headstock.
**Set the drive center into the workpiece with a soft mallet prior to installing it on the headstock.
* Touch your project by hand while the lathe is running
