533
edits
Changes
From Pumping Station One
→Auth/Use Notes
== Auth/Use Notes ==
== Auth/Use Notes ==
The following are prerequisites for authorization on the LeBlond
1 Tier 1 Cold Metals authorization
2 Canvas LeBlond course
Base skills for authorization:
1. Safety
2. Power, fwd, neutral, break, rev
3. Basic maintenance - Oil ports, oiler
4. Familiarity with controls - Z axis, Y axis, compound, auto feed, speeds
5. 3 jaw chuck
6. Tool post, tool selection
7. Face cut
8. Tail stock support
9. Longitudinal cut, cut to size
10. Cleanup
== To-Do ==
== To-Do ==
|
|
|-
|-
|todo
|done
|purchase 3mt dead center
|purchase 3mt dead center
|
|
== Maintenance ==
== Maintenance ==
Removing the chuck. Our chuck is bigger, L01 rather than the L00 in this video, but the video shows some interesting pointers about seating the chuck : https://www.youtube.com/watch?v=tsM1pRpTciY
Removing the chuck. This video shows some interesting pointers about seating the chuck : https://www.youtube.com/watch?v=tsM1pRpTciY
If you find problems with the high speeds check the coged belt in the headstock ( 27" 54t 1" wide McMaster Part: https://www.mcmaster.com/6484k172 To replace the belt remove the four screws holding the retaining ring and the retaining ring from the coged gear, work the belt out, it can be removed without removing any other gears.
== Equipment ==
== Equipment ==
Jacobs Spindle Nose Collet Chuck " A very nice piece of tooling", this video is worth it for the music alone - https://www.youtube.com/watch?v=smKWlrjxXag
Jacobs Spindle Nose Collet Chuck " A very nice piece of tooling", this video is worth it for the music alone - https://www.youtube.com/watch?v=smKWlrjxXag
Shars Tool set : 404-1054main_2.jpg
Shars Tool set available:
<gallery>
File:404-1054main_2.jpg|SHARS Sku 404-1054
File:404-1054sketch.jpg|
File:404-1056Main.jpg|DCMT3 Insert SHARS Sku 404-1060
File:404-1061Main.jpg|CCMT3 Carbide Insert SHARS Sku 404-1061
File:404-1069Main.jpg|WCMX Carbide Insert SHARS Sku 404-1069
File:424-1381Main.jpg|AG60 External V Partial Profile AG60 Carbide Threading SHARS Sku 424-1381
File:404-2346a.jpg|Boring Bar 3/4 uses DC## insert
</gallery>
Insert Tools:
Insert Tools:
SCLCL5/8 CC** 32.5 T15 M4x10
SCLCL5/8 CCMT3 (SHARS SKU404-1061) 32.5 T15 M4x10
SCLCR5/8 CC** 32.5 T15 M4x10
SCLCR5/8 CCMT3 (SHARS SHU404-1061) 32.5 T15 M4x10
SER5/8 -16 16ER T15 M3.5x12 LT16R
SER5/8 -16 16ER T15 M3.5x12 LT16R
SDNCN5/8 DCMT3 (SHARS SKU 404=1060) 32.5 T15 M4x10
SDNCN5/8 DCMT3 (SHARS SKU 404=1060) 32.5 T15 M4x10
SWGCR5/8 WC** 32.5 T15 M4x10
SWGCR5/8 WCMX (SHARS SkU 404-1069) 32.5 T15 M4x10
SDJCR5/8 DC** 32.5 T15 M4x10
SDJCR5/8 DC** 32.5 T15 M4x10
MGEHR5/8-3 MGMN300 32.5 T15 M4x10
MGEHR5/8-3 MGMN300 32.5 T15 M4x10
boring bar Shars S12S-SDUCR3 3/4"x 1.25" uses DC##32.5 insert T15 M4x10 screw
== References ==
== References ==
Manual -> https://wiki.pumpingstationone.org/images/LeBlond_Regal.pdf
Manual -> https://wiki.pumpingstationone.org/images/LeBlond_Regal.pdf
Schematic -> https://wiki.pumpingstationone.org/images/EE700_Electrical_Drawings.pdf
Schematic with changes for E Switch -> https://wiki.pumpingstationone.org/images/LeBlond_w_E_Switch_Small.jpg
== List of Currently Authorized Users ==
== List of Currently Authorized Users ==
!Comments
!Comments
|-
|-
|
|Charles Ware
|
|Jim Brink
|8/3/19
|
|
|-
|Ryan Pierce
|Jim Brink
|8/7/19
|
|
|-
|-
|
|Bill Hunt
|Jim Brink
|8/24/19
|
|
|-
|[[User:mct|McTavish McArdle]]
|Jim Brink
|2019-10-19
|
|
|-
|[[User:rchace|Raymond Chace]]
|Jim Brink
|11/16/19
|
|-
|[[User:sranjb2|Shayan Ranjbari]]
|Jim Brink
|07/25/2020
|-
|[[User:tcummings|Tom Cummings]]
|Jim Brink
|10/17/2020
|
|-
|}
[[Category:Shop Equipment]]
[[Category:Shop Equipment]]
[[Category:Equipment]]
[[Category:Equipment]]
[[Category: Cold Metals]]
[[Category: Cold Metals]]
