Difference between revisions of "Lincoln Electric 3200HD"
Jump to navigation
Jump to search
Line 12: | Line 12: | ||
|hostarea = Hotmetals | |hostarea = Hotmetals | ||
}} | }} | ||
+ | |||
+ | Essentially "a hot melt glue gun for metals". It releases 75% argon / 25% CO2 gas as you weld to prevent oxidation of the metal. You're melting the metals you're joining, and adding a bead as well. | ||
+ | |||
+ | == Safety == | ||
+ | * Wear natural fibers (cotton, wool) only. It puts out sparks and can melt synthetics onto your skin. | ||
+ | * Wear closed-toe shoes, unless you like setting your feet on fire. | ||
+ | * Cover all skin - it puts out a lot of UV light. You'll get a sunburn, guaranteed. Plus, you can get burned. | ||
+ | * It's a good idea to have a hat or something under the face shield, as sparks will go onto the top of your head. | ||
+ | * There are two screens on wheels - arrange them to block UV light from going to the rest of the shop. | ||
+ | * Use the thick gloves, also the face shield. The face shield for MIG is pretty handy, it darkens when you start welding. | ||
+ | * Yell "welding" before starting so anyone sneaking up on you is aware to avert their eyes. | ||
+ | * The piece will be hot for a long time after you welded it. You can grab it with tongs and dip in buckets. | ||
+ | |||
+ | == Approximate Steps for Use == | ||
+ | |||
+ | === Preparation === | ||
+ | # Pull out the machine | ||
+ | # Clean out welding tip with the pliers that have files on the outside of the jaws. | ||
+ | # Check inside if it's wired for MIG. There's a diagram on the inside of the case. This should not change but can. | ||
+ | ## The reel of metal wire size should match your recommended diameter. | ||
+ | ## Wire adjustment is much like the 3D printers' - it flips up and has a tension holder | ||
+ | # Also check the recommended settings for welding. You will need to know a letter and a number. | ||
+ | # Set the recommended settings on the front panel. | ||
+ | # Plug it in. | ||
+ | # Cut the wire tip using the pliers to the recommended length. | ||
+ | # Check that the gas pressure is above 500PSI. If it's below, press the button on the left wall that will tell Ron to order more gas. | ||
+ | ## Not sure if can use below 500PSI - I think we're fine as long as it outputs 20PSI? | ||
+ | # Adjust gas output on machine to 20PSI | ||
+ | # Attach the ground to either the table or the part, depending on what you're doing. | ||
+ | |||
+ | === Use === | ||
+ | * Close the screens behind you. | ||
+ | * Check around periodically for stuff you set on fire. This thing puts out hot sparks. I set a rag on fire the first time I used it. I was confused why the authorizer had brought a smoldering rag for authorization - nope, that was me. | ||
+ | * You may want to brush the joints before welding. Be sure to pay attention to the labeling on the metal brush - steel only. | ||
+ | * It may be a good idea to tack both ends of the parts being welded. | ||
+ | * Make sure there's no crimps in the tube feeding the metal wire. It should be as straight as possible. | ||
+ | * Ideally you would weld at about a 45° angle. | ||
+ | * If welding something perpendicular, you're trying to make a puddle (bead) that equally touches both parts. You'll angle it towards the top piece slightly more. | ||
+ | * Yell "Welding" before starting. | ||
+ | * The machine has a duty cycle of 2 minutes for every 10. That means you can only use the machine for 2 minutes before taking a break to let it cool down. In practice you usually won't have a problem with this, but for longer, and multiple welds, pay attention to this. | ||
+ | |||
+ | === When Done === | ||
+ | # Turn off gas. | ||
+ | # Pull trigger til the PSI reaches 0. | ||
+ | # Nice to cut off the extra wire you just fed in the above step. | ||
+ | # Unplug. | ||
+ | # Coil up everything and put back. | ||
+ | # Brush off the mess from the table like the fine, upstanding citizen you are. | ||
+ | # Put away anything else you got out, like metals, gloves, face mask. | ||
+ | |||
== Status == | == Status == |
Revision as of 11:43, 2 October 2016
Essentially "a hot melt glue gun for metals". It releases 75% argon / 25% CO2 gas as you weld to prevent oxidation of the metal. You're melting the metals you're joining, and adding a bead as well.
Safety
- Wear natural fibers (cotton, wool) only. It puts out sparks and can melt synthetics onto your skin.
- Wear closed-toe shoes, unless you like setting your feet on fire.
- Cover all skin - it puts out a lot of UV light. You'll get a sunburn, guaranteed. Plus, you can get burned.
- It's a good idea to have a hat or something under the face shield, as sparks will go onto the top of your head.
- There are two screens on wheels - arrange them to block UV light from going to the rest of the shop.
- Use the thick gloves, also the face shield. The face shield for MIG is pretty handy, it darkens when you start welding.
- Yell "welding" before starting so anyone sneaking up on you is aware to avert their eyes.
- The piece will be hot for a long time after you welded it. You can grab it with tongs and dip in buckets.
Approximate Steps for Use
Preparation
- Pull out the machine
- Clean out welding tip with the pliers that have files on the outside of the jaws.
- Check inside if it's wired for MIG. There's a diagram on the inside of the case. This should not change but can.
- The reel of metal wire size should match your recommended diameter.
- Wire adjustment is much like the 3D printers' - it flips up and has a tension holder
- Also check the recommended settings for welding. You will need to know a letter and a number.
- Set the recommended settings on the front panel.
- Plug it in.
- Cut the wire tip using the pliers to the recommended length.
- Check that the gas pressure is above 500PSI. If it's below, press the button on the left wall that will tell Ron to order more gas.
- Not sure if can use below 500PSI - I think we're fine as long as it outputs 20PSI?
- Adjust gas output on machine to 20PSI
- Attach the ground to either the table or the part, depending on what you're doing.
Use
- Close the screens behind you.
- Check around periodically for stuff you set on fire. This thing puts out hot sparks. I set a rag on fire the first time I used it. I was confused why the authorizer had brought a smoldering rag for authorization - nope, that was me.
- You may want to brush the joints before welding. Be sure to pay attention to the labeling on the metal brush - steel only.
- It may be a good idea to tack both ends of the parts being welded.
- Make sure there's no crimps in the tube feeding the metal wire. It should be as straight as possible.
- Ideally you would weld at about a 45° angle.
- If welding something perpendicular, you're trying to make a puddle (bead) that equally touches both parts. You'll angle it towards the top piece slightly more.
- Yell "Welding" before starting.
- The machine has a duty cycle of 2 minutes for every 10. That means you can only use the machine for 2 minutes before taking a break to let it cool down. In practice you usually won't have a problem with this, but for longer, and multiple welds, pay attention to this.
When Done
- Turn off gas.
- Pull trigger til the PSI reaches 0.
- Nice to cut off the extra wire you just fed in the above step.
- Unplug.
- Coil up everything and put back.
- Brush off the mess from the table like the fine, upstanding citizen you are.
- Put away anything else you got out, like metals, gloves, face mask.
Status
Standard electric power plug has been replaced with a NEMA 5-20 type plug, plugs right into the wall socket there but won't plug into a power strip or extension cord.
Some Info
http://www.4x4review.com/lincoln-eletrics-weld-pak-3200-hd-mig-welder/
List of Currently Authorized Users
Authorized Member Keon Turner | Authorized By |
---|---|
Alejandro Drexler | Ron Olson |
Chris Agocs | Ron Olson |
Yousef Zaffarkhan | Ron Olson |
Andy Larkin | Ron Olson |
Samuel Sion | Ron Olson |
Lauren Svedman | Ron Olson |
Aaron Carlock | Ron Olson |
Greg Kudlacz | Ron Olson |
Daniel Maziarz | Ron Olson |
Connor Sullivan | Tom Judge |
Keith Couture | Ron Olson |
Jordan Montes | Ron Olson |
Ken Burkhardt | Ron Olson |
Sam Olendorf | Ron Olson |
Eugene Liokumovich | Ron Olson |
Matt Keith | Ron Olson |
Juan Ramos | Jeremy Bloyd-Peshkin |
Ashley Matrisciano | Jeremy Bloyd-Peshkin |
Burton Kent | Jeremy Bloyd-Peshkin |