4
edits
Changes
Jump to navigation
Jump to search
Line 1:
Line 1: − + Line 15:
Line 15: − == Safety ==+ − * Wear natural fibers (cotton, wool) only. It puts out sparks and can melt synthetics onto your skin. − * Wear closed-toe shoes, unless you like setting your feet on fire. − * Cover all skin - it puts out a lot of UV light. You'll get a sunburn, guaranteed. Plus, you can get burned. − * It's a good idea to have a hat or something under the face shield, as sparks will go onto the top of your head. − * There are two screens on wheels - arrange them to block UV light from going to the rest of the shop. − * Use the thick gloves, also the face shield. The face shield for MIG is pretty handy, it darkens when you start welding. − * Yell "welding" before starting so anyone sneaking up on you is aware to avert their eyes. − * The piece will be hot for a long time after you welded it. You can grab it with tongs and dip in buckets. − == Approximate Steps for Use == − − === Preparation === − # Pull out the machine − # Clean out welding tip with the pliers that have files on the outside of the jaws. − # Check inside if it's wired for MIG. There's a diagram on the inside of the case. This should not change but can. − ## The reel of metal wire size should match your recommended diameter. − ## Wire adjustment is much like the 3D printers' - it flips up and has a tension holder − # Also check the recommended settings for welding. You will need to know a letter and a number. − # Set the recommended settings on the front panel. − # Plug it in. − # Cut the wire tip using the pliers to the recommended length. − # Check that the gas pressure is above 500PSI. If it's below, press the button on the left wall that will tell Ron to order more gas. − ## Not sure if can use below 500PSI - I think we're fine as long as it outputs 20CFH? − # Adjust gas output on machine to 20CFH − # Attach the ground to either the table or the part, depending on what you're doing. − − === Use === − * Close the screens behind you. − * Check around periodically for stuff you set on fire. This thing puts out hot sparks. I set a rag on fire the first time I used it. I was confused why the authorizer had brought a smoldering rag for authorization - nope, that was me. − * You may want to brush the joints before welding. Be sure to pay attention to the labeling on the metal brush - steel only. − * It may be a good idea to tack both ends of the parts being welded. − * Make sure there's no crimps in the tube feeding the metal wire. It should be as straight as possible. − * Ideally you would weld at about a 45° angle. − * If welding something perpendicular, you're trying to make a puddle (bead) that equally touches both parts. You'll angle it towards the top piece slightly more. − * Yell "Welding" before starting. − * The machine has a duty cycle of 2 minutes for every 10. That means you can only use the machine for 2 minutes before taking a break to let it cool down. In practice you usually won't have a problem with this, but for longer, and multiple welds, pay attention to this. − − === When Done === − # Turn off gas. − # Pull trigger til the PSI reaches 0. − # Nice to cut off the extra wire you just fed in the above step. − # Unplug. − # Coil up everything and put back. − # Brush off the mess from the table like the fine, upstanding citizen you are. − # Put away anything else you got out, like metals, gloves, face mask. Line 68:
Line 24: + + + + + + + + + + + + + + + + + + + + + + + + + + + + − + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +
Lincoln Electric 3200HD (view source)
Revision as of 03:49, 25 February 2020
, 03:49, 25 February 2020→List of Currently Authorized Users
{{Template:EquipmentPage
{{Template:EquipmentPage
|owner = Pumping Station One
|owner = PS:One
|certification = yes
|certification = yes
|hackable = no
|hackable = no
Essentially "a hot melt glue gun for metals". It releases 75% argon / 25% CO2 gas as you weld to prevent oxidation of the metal. You're melting the metals you're joining, and adding a bead as well.
Essentially "a hot melt glue gun for metals". It releases 75% argon / 25% CO2 gas as you weld to prevent oxidation of the metal. You're melting the metals you're joining, and adding a bead as well.
For safety tips and a general operational overview, see the article on PS1's [[MIG welders]].
== Status ==
== Status ==
== Some Info ==
== Some Info ==
http://www.4x4review.com/lincoln-eletrics-weld-pak-3200-hd-mig-welder/
http://www.4x4review.com/lincoln-eletrics-weld-pak-3200-hd-mig-welder/
== List of Currently Authorized Users ==
== List of Currently Authorized Users ==
{| class="wikitable" border="1"
{| class="wikitable" border="1"
! Authorized Member Keon Turner
! Authorized Member Keon Turner
! Authorized By
! Authorized By
! Date
|-
|-
|Alejandro Drexler
|Alejandro Drexler
|Ron Olson
|Ron Olson
|
|-
|-
|Chris Agocs
|Chris Agocs
|Ron Olson
|Ron Olson
|
|-
|Ray Doeksen
|Ron Olson & Lauren Svedman
|
|-
|-
|Yousef Zaffarkhan
|Yousef Zaffarkhan
|Ron Olson
|Ron Olson
|
|-
|-
|Andy Larkin
|Andy Larkin
|Ron Olson
|Ron Olson
|
|-
|-
|Samuel Sion
|Samuel Sion
|Ron Olson
|Ron Olson
|
|-
|-
|Lauren Svedman
|Lauren Svedman
|Ron Olson
|Ron Olson
|
|-
|-
|Aaron Carlock
|Aaron Carlock
|Ron Olson
|Ron Olson
|
|-
|-
|Greg Kudlacz
|Greg Kudlacz
|Ron Olson
|Ron Olson
|
|-
|-
|Daniel Maziarz
|Daniel Maziarz
|Ron Olson
|Ron Olson
|
|-
|-
|Connor Sullivan
|Connor Sullivan
|Tom Judge
|Tom Judge
|
|-
|-
|Keith Couture
|Keith Couture
|Ron Olson
|Ron Olson
|
|-
|-
|Jordan Montes
|Jordan Montes
|Ron Olson
|Ron Olson
|
|-
|-
|Ken Burkhardt
|Ken Burkhardt
|Ron Olson
|Ron Olson
|
|-
|-
|Sam Olendorf
|Sam Olendorf
|Ron Olson
|Ron Olson
|
|-
|-
|Eugene Liokumovich
|Eugene Liokumovich
|Ron Olson
|Ron Olson
|
|-
|-
|[[user:mkeith|Matt Keith]]
|[[user:mkeith|Matt Keith]]
|Ron Olson
|Ron Olson
|
|-
|-
|[[user:panchan99|Juan Ramos]]
|[[user:panchan99|Juan Ramos]]
|Jeremy Bloyd-Peshkin
|Jeremy Bloyd-Peshkin
|
|-
|-
|[[user:smash|Ashley Matrisciano]]
|[[user:smash|Ashley Matrisciano]]
|Jeremy Bloyd-Peshkin
|Jeremy Bloyd-Peshkin
|
|-
|-
|[[user:smash|Burton Kent]]
|[[user:smash|Burton Kent]]
|Jeremy Bloyd-Peshkin
|Jeremy Bloyd-Peshkin
|
|-
|-
|Brian Cuocci
|Brian Cuocci
|Ron Olson
|Ron Olson
|
|-
|-
|Sam Paris
|Sam Paris
|Ron Olson
|Ron Olson
|
|-
|-
|Clarence Bartenhagen
|Clarence Bartenhagen
|Chris Iacullo
|Chris Iacullo
|
|-
|-
|[[user:Pedrosk|Ed Breuer]]
|[[user:Pedrosk|Ed Breuer]]
|Chris Iacullo
|Chris Iacullo
|Feb 2017
|Feb 2017
|}
|-
| Matthew Kim
| Chris Iacullo
|
|-
| [[User:Andrewvaughan|Andrew Vaughan]]
| Chris Iacullo
| May 11, 2017
|-
| Miriam Stevens
| Chris Iacullo
| July 27, 2017
|-
| Daron Wooding
| Touly Phiachantharath
|
|-
| Wally Ibrahim
| Daron Wooding
| 10/21/17
|-
| Stephanie Pelzer
| Chris Iacullo
| 1/11/18
|-
| Chris Versteeg
| Chris Iacullo
| 1/11/18
|-
| Kari Danek
| Chris Iacullo
| 1/25/18
|-
| Mike Ice
| Daron Wooding
| 2/17/18
|-
| Brandon Kennedy
| Daron Wooding
| 3/17/18
|-
| Aaron Vander Bee
| Daron Wooding
| 3/17/18
|-
| Wayne Hendryx
| Chris Iacullo
| 4/11/18
|-
| Lucas Goossen
| Daron Wooding
| 4/28/18
|-
| Nick Prorok
| Chris Iacullo
| 6/07/18
|-
| Mark Treiber
| Chris Iacullo
| 8/16/2018
|-
| Jacob Dawson
| ?Daron
| 9/22/2018
|-
| Jim Lund
| Daron Wooding
| 12/01/18
|-
| Tatjana Paunesku (tpaune)
| Daron Wooding
| 12/01/18
|-
| Tom Henderson (chiral)
| Daron Wooding
| 05/04/19
|-
| Lavande Chou
| Daron Wooding
| 09/07/19
|-
| Paul Lukas
| Daron Wooding
| 09/07/19
|-
| Tony Vetter
| Daron Wooding
| 10/19/19
|-
| Corwin Kline
| Daron?
| 2/22/2020
|-
| Martin Deng
| Daron Wooding
| 2/22/2020
|-
| Erick Santiago
| Daron Wooding
| 2/22/2020
|-}
[[Category: Hot Metals]]
[[Category: Hot Metals]]