42
edits
Changes
From Pumping Station One
Sherline 8 inch lathe + milling column (view source)
Revision as of 19:25, 7 July 2020
, 19:25, 7 July 2020→Inventory
...and... at the moment we're still sorting it out for use at PS1.
...and... at the moment we're still sorting it out for use at PS1.
= Major Specs =
While this machine has '''metric''' lead screws and handwheels, it is dimensioned in inches. It's OK, just don't try to land it on Mars.
: '''lathe''' : 3.5" swing, 8" between centers, or 4.75" swing single-ended with headstock spacer; 1/4" square tooling
: '''mill''' : 6.25" Z travel, 4.25" crosslide travel, 2.25" throat (3.5" with spacer); 3/8" tool holder
: '''power''' : 60W DC motor with speed control
: '''speed''' : 70-2800 rpm or 35-1400 rpm
= larval tool page blather =
= larval tool page blather =
* Tommy Bar
* Tommy Bar
* Head Alignment Key
* Head Alignment Key
* tool post assembly
* fixed tool post assembly
* tool post assembly '''missing rocker'''
| morse #1 rusty
| morse #1 rusty
[https://sherline.com/wp-content/uploads/2015/01/5326_instructions_v8_web.pdf PDF] is a 50-page book with a lot to say about the machine, machining and machining on this machine.
[https://sherline.com/wp-content/uploads/2015/01/5326_instructions_v8_web.pdf PDF] is a 50-page book with a lot to say about the machine, machining and machining on this machine.
| [https://sherline.com/wp-content/uploads/2015/09/2090inst.pdf PDF]
| [https://sherline.com/wp-content/uploads/2015/09/2090inst.pdf PDF]
|
|
| use with drawbolt? (not included)
|
* use with drawbolt? (not included)
* '''missing 6 July 2020'''
|-
|-
| Gear Cutters
| Gear Cutters
|
|
|
|
* '''missing 6 July 2020'''
|-
|-
| Crosslide Accessory Plate
| Crosslide Accessory Plate
| '''missing drawbolt+washer'''
| '''missing drawbolt+washer'''
|
|
* '''missing 6 July 2020'''
|-
|-
| Slitting Saw ['''which one?''']
| Slitting Saw ['''which one?''']
|
|
|
|
* '''missing 6 July 2020'''
|-
|-
| End Mill Holder (3/8")
| End Mill Holder (3/8")
* 2x (Sherline T-nut + L-clamp + 10-32 x '''5/8"''' SHC screw)
* 2x (Sherline T-nut + L-clamp + 10-32 x '''5/8"''' SHC screw)
* 2x (Sherline T-nut + 10-32 x '''1/2"''' SHC screw)
* 2x (Sherline T-nut + 10-32 x '''1/2"''' SHC screw)
** '''missing'''
** '''nuts missing'''
* 4x (10-32 x '''3/16"''' set screw)
* 4x (10-32 x '''3/16"''' set screw)
** '''present?/missing?'''
** have 2
** '''missing 2'''
* Hold Down Tab + 2x (10-32 x '''3/8"''' SHC screw)
* Hold Down Tab + 2x (10-32 x '''3/8"''' SHC screw)
|
|
** '''missing one'''
** '''missing one'''
* 4x (10-32 x '''3/8"''' SHC screw)
* 4x (10-32 x '''3/8"''' SHC screw)
* 10/32 x '''3/8"''' set screw
* 10/32 x '''3/8"''' set screw
* 10-32 x '''1"''' SHC screw
* 10-32 x '''1"''' SHC screw
