Line 21: |
Line 21: |
| | | |
| = Major Specs = | | = Major Specs = |
| + | |
| + | While this machine has '''metric''' lead screws and handwheels, it is dimensioned in inches. It's OK, just don't try to land it on Mars. |
| | | |
| : '''lathe''' : 3.5" swing, 8" between centers, or 4.75" swing single-ended with headstock spacer; 1/4" square tooling | | : '''lathe''' : 3.5" swing, 8" between centers, or 4.75" swing single-ended with headstock spacer; 1/4" square tooling |
Line 26: |
Line 28: |
| : '''power''' : 60W DC motor with speed control | | : '''power''' : 60W DC motor with speed control |
| : '''speed''' : 70-2800 rpm or 35-1400 rpm | | : '''speed''' : 70-2800 rpm or 35-1400 rpm |
− |
| |
| | | |
| = larval tool page blather = | | = larval tool page blather = |
Line 103: |
Line 104: |
| * Tommy Bar | | * Tommy Bar |
| * Head Alignment Key | | * Head Alignment Key |
− | * tool post assembly | + | * fixed tool post assembly |
| + | * tool post assembly '''missing rocker''' |
| | morse #1 rusty | | | morse #1 rusty |
| [https://sherline.com/wp-content/uploads/2015/01/5326_instructions_v8_web.pdf PDF] is a 50-page book with a lot to say about the machine, machining and machining on this machine. | | [https://sherline.com/wp-content/uploads/2015/01/5326_instructions_v8_web.pdf PDF] is a 50-page book with a lot to say about the machine, machining and machining on this machine. |
Line 133: |
Line 135: |
| | [https://sherline.com/wp-content/uploads/2015/09/2090inst.pdf PDF] | | | [https://sherline.com/wp-content/uploads/2015/09/2090inst.pdf PDF] |
| | | | | |
− | | use with drawbolt? (not included) | + | | |
| + | * use with drawbolt? (not included) |
| + | * '''missing 6 July 2020''' |
| |- | | |- |
| | Gear Cutters | | | Gear Cutters |
Line 140: |
Line 144: |
| | | | | |
| | | | | |
| + | * '''missing 6 July 2020''' |
| |- | | |- |
| | Crosslide Accessory Plate | | | Crosslide Accessory Plate |
Line 152: |
Line 157: |
| | '''missing drawbolt+washer''' | | | '''missing drawbolt+washer''' |
| | | | | |
| + | * '''missing 6 July 2020''' |
| |- | | |- |
| | Slitting Saw ['''which one?'''] | | | Slitting Saw ['''which one?'''] |
Line 158: |
Line 164: |
| | | | | |
| | | | | |
| + | * '''missing 6 July 2020''' |
| |- | | |- |
| | End Mill Holder (3/8") | | | End Mill Holder (3/8") |
Line 189: |
Line 196: |
| * 2x (Sherline T-nut + L-clamp + 10-32 x '''5/8"''' SHC screw) | | * 2x (Sherline T-nut + L-clamp + 10-32 x '''5/8"''' SHC screw) |
| * 2x (Sherline T-nut + 10-32 x '''1/2"''' SHC screw) | | * 2x (Sherline T-nut + 10-32 x '''1/2"''' SHC screw) |
− | ** '''missing''' | + | ** '''nuts missing''' |
| * 4x (10-32 x '''3/16"''' set screw) | | * 4x (10-32 x '''3/16"''' set screw) |
− | ** '''present?/missing?''' | + | ** have 2 |
| + | ** '''missing 2''' |
| * Hold Down Tab + 2x (10-32 x '''3/8"''' SHC screw) | | * Hold Down Tab + 2x (10-32 x '''3/8"''' SHC screw) |
| | | | | |
Line 206: |
Line 214: |
| ** '''missing one''' | | ** '''missing one''' |
| * 4x (10-32 x '''3/8"''' SHC screw) | | * 4x (10-32 x '''3/8"''' SHC screw) |
− | ** '''?all present?'''
| |
| * 10/32 x '''3/8"''' set screw | | * 10/32 x '''3/8"''' set screw |
| * 10-32 x '''1"''' SHC screw | | * 10-32 x '''1"''' SHC screw |