425
edits
Changes
From Pumping Station One
New page
= Jet Wood Lathe =
{{Template:EquipmentPage
|image =
|owner = Joeseph Nudell
|serial = NAN
|certification = yes
|hackable = no
|model = Jet 1236
|arrived = 6/1/14
|doesitwork = yes
|contact = Joeseph Nudell
|where = Woodshop
|value = 800
|itemphoto =
}}
'''This tool requires certification for use.'''
==PERSONAL PROTECTIVE EQUIPMENT==
* Face shield or safety glasses must be worn.
* Long and loose hair must be contained.
* Do not wear gloves or loose clothing.
* Remove watches,rings,and other jewelry.
* Don't wear or roll up long sleeves.
* Hearing protection may be required.
* Dust protection may be required.
==PRE-OPERATIONAL SAFETY CHECKS==
*Locate and ensure you are familiar with all machine operations and controls.
*Ensure all guards are fitted, secure and functional. Do not operate if guards are missing or faulty.
*Workpiece must be securely fastened to face plate, chuck or between centers.
*Adjust speed to suit the diameter of the work and turning operation.
*Rotate the workpiece by hand to check clearance between tool rest and bed.
*Ensure the cutting tools are sharp and in good condition.
*Start the dust extraction unit before using the machine.
*Make sure all clamping handles are tight,
==OPERATIONAL SAFETY CHECKS==
*Before making adjustments, switch off and bring the machine to a complete standstill.
*Keep the tool rest adjusted close to the work and at the correct height.
*Adjust speed to suit the diameter of the work and turning operation.
*Stop the lathe and remove all tool rests before sanding.
==ENDING OPERATIONS AND CLEANING UP==
*Switch off the machine when work completed.
*Return all chisels and other tools to racks.
*Leave the machine in a safe, clean and tidy state.
==POTENTIAL HAZARDS AND INJURIES==
*Eye injuries from flying debris or defective timber.
*Hair/clothing getting caught in moving machine parts.
*Airborne dust.
==DO==
* Rough cut the workpiece as close as possible to the finished shape before installing it.
* Check your workpiece for flaws, cracks, knots etc.and test glue joints before mounting the workpiece on machine.
* Use the lowest speed when starting a new workpiece.
* Remove the tool rest before sanding or polishing.
==DON'T==
* Drive the workpiece into the drive center while the drive center is in the headstock.
**Set the drive center into the workpiece with a soft mallet prior to installing it on the headstock.
== List of Currently Certified Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
|-
|-
|}
==Documentation==
[[Category:Woodworking]]
[[Category:Shop Equipment]]
{{Template:EquipmentPage
|image =
|owner = Joeseph Nudell
|serial = NAN
|certification = yes
|hackable = no
|model = Jet 1236
|arrived = 6/1/14
|doesitwork = yes
|contact = Joeseph Nudell
|where = Woodshop
|value = 800
|itemphoto =
}}
'''This tool requires certification for use.'''
==PERSONAL PROTECTIVE EQUIPMENT==
* Face shield or safety glasses must be worn.
* Long and loose hair must be contained.
* Do not wear gloves or loose clothing.
* Remove watches,rings,and other jewelry.
* Don't wear or roll up long sleeves.
* Hearing protection may be required.
* Dust protection may be required.
==PRE-OPERATIONAL SAFETY CHECKS==
*Locate and ensure you are familiar with all machine operations and controls.
*Ensure all guards are fitted, secure and functional. Do not operate if guards are missing or faulty.
*Workpiece must be securely fastened to face plate, chuck or between centers.
*Adjust speed to suit the diameter of the work and turning operation.
*Rotate the workpiece by hand to check clearance between tool rest and bed.
*Ensure the cutting tools are sharp and in good condition.
*Start the dust extraction unit before using the machine.
*Make sure all clamping handles are tight,
==OPERATIONAL SAFETY CHECKS==
*Before making adjustments, switch off and bring the machine to a complete standstill.
*Keep the tool rest adjusted close to the work and at the correct height.
*Adjust speed to suit the diameter of the work and turning operation.
*Stop the lathe and remove all tool rests before sanding.
==ENDING OPERATIONS AND CLEANING UP==
*Switch off the machine when work completed.
*Return all chisels and other tools to racks.
*Leave the machine in a safe, clean and tidy state.
==POTENTIAL HAZARDS AND INJURIES==
*Eye injuries from flying debris or defective timber.
*Hair/clothing getting caught in moving machine parts.
*Airborne dust.
==DO==
* Rough cut the workpiece as close as possible to the finished shape before installing it.
* Check your workpiece for flaws, cracks, knots etc.and test glue joints before mounting the workpiece on machine.
* Use the lowest speed when starting a new workpiece.
* Remove the tool rest before sanding or polishing.
==DON'T==
* Drive the workpiece into the drive center while the drive center is in the headstock.
**Set the drive center into the workpiece with a soft mallet prior to installing it on the headstock.
== List of Currently Certified Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
|-
|-
|}
==Documentation==
[[Category:Woodworking]]
[[Category:Shop Equipment]]
