Difference between revisions of "Evenheat 810 Kiln"
Jump to navigation
Jump to search
m (Robot: Cosmetic changes) |
|||
Line 1: | Line 1: | ||
− | {{Template:EquipmentPage |owner=PS:One |model=Evenheat 810 |serial=38008 |arrived=2010 |doesitwork=Yes |contact=Eric Stein |where=? |certification=yes |hackable=no |value=$865}}<br> | + | {{Template:EquipmentPage |owner=PS:One |model=Evenheat 810 |serial=38008 |arrived=2010 |doesitwork=Yes |contact=Eric Stein |where=? |certification=yes |hackable=no |value=$865}}<br /> |
− | ==History== | + | == History == |
− | On 1/28/2013 this was tested to at least power up and create heat. <br> | + | On 1/28/2013 this was tested to at least power up and create heat. <br /> |
− | 3/3/2014. Inspect and test all mechanical and electrical components. <br> | + | 3/3/2014. Inspect and test all mechanical and electrical components. <br /> |
− | Remove upper switch, disassemble, clean contacts, reassemble and reinstall. <br> | + | Remove upper switch, disassemble, clean contacts, reassemble and reinstall. <br /> |
All components appear to works as intended. | All components appear to works as intended. | ||
− | ==Heating Profile== | + | == Heating Profile == |
− | On 3/3/2014 I ran the kiln using a PID temperature controller set to 2200f. <br> | + | On 3/3/2014 I ran the kiln using a PID temperature controller set to 2200f. <br /> |
− | Room temp to 500f. | + | Room temp to 500f. 7 min. <br /> |
− | Room temp to 1000f. | + | Room temp to 1000f. 17 min. <br /> |
− | Room temp to 1500f. | + | Room temp to 1500f. 40 min. <br /> |
− | Room temp to 2000f. | + | Room temp to 2000f. 95 min. |
− | ==Important Documents== | + | == Important Documents == |
− | *[http://www.evenheat-kiln.com/pdf/manual-c-810.pdf | + | * [http://www.evenheat-kiln.com/pdf/manual-c-810.pdf Manual] |
− | *[http://www.evenheat-kiln.com/pdf/manual-c-kiln-sitter-with-limit-timer.pdf Controller Manual] | + | * [http://www.evenheat-kiln.com/pdf/manual-c-kiln-sitter-with-limit-timer.pdf Controller Manual] |
− | *[http://www.evenheat-kiln.com/ceramic/technical/ Manufacturer's technical information] | + | * [http://www.evenheat-kiln.com/ceramic/technical/ Manufacturer's technical information] |
− | [[ | + | |
+ | [[Category:Photographs Needed]] | ||
[[Category:Shop Equipment]] | [[Category:Shop Equipment]] | ||
[[Category:Fabrication]] | [[Category:Fabrication]] | ||
[[Category:Craft]] | [[Category:Craft]] | ||
[[Category:Pottery]] | [[Category:Pottery]] |
Revision as of 00:11, 18 March 2014
Owner/Loaner | PS:One |
---|---|
Serial Number | 38008 |
Make/Model | Evenheat 810 |
Arrival Date | 2010 |
Usability | Yes |
Contact | Eric Stein |
Where | ? |
Authorization Needed | yes |
Hackable | no |
Estimated Value | $865 |
Host Area | {{{hostarea}}} |
History
On 1/28/2013 this was tested to at least power up and create heat.
3/3/2014. Inspect and test all mechanical and electrical components.
Remove upper switch, disassemble, clean contacts, reassemble and reinstall.
All components appear to works as intended.
Heating Profile
On 3/3/2014 I ran the kiln using a PID temperature controller set to 2200f.
Room temp to 500f. 7 min.
Room temp to 1000f. 17 min.
Room temp to 1500f. 40 min.
Room temp to 2000f. 95 min.