Difference between revisions of "Jet Wood Lathe"
(→List of Currently Certified Users)
|Line 170:||Line 170:|
Revision as of 15:02, 15 March 2017
|Host Area||Wood Shop|
- 1 Authorization for this tool by authorized proctors only
- 1.1 Authorized Proctors
- 1.2 Resources
- 1.3 Personal Protective Equipment
- 1.4 Pre-Operational Safety Checks
- 1.5 Operational Safety Checks
- 1.6 Ending Operations and Cleaning Up
- 1.7 Potential Hazards and Injuries
- 1.8 Do
- 1.9 Don't
- 1.10 How To Get Certified
- 1.11 List of Currently Certified Users
- 1.12 Documentation
This tool requires certification for use.
This tool requires certification for use. Please contact one of the following to arrange authorization.
- This list is a basic starting point pending approval of the area host.
|Matt Triano||matt.triano @ gmail.com|
|Eric Beauchamp — area host||eric @ home-chicago.com|
|Sevin Strauss — approved authorizer|
|Andrew Camardella — approved authorizer|
Personal Protective Equipment
- Face shield (not just safety glasses) must be worn.
- Long and loose hair must be contained.
- Do not wear gloves or loose clothing.
- Remove watches, rings, and other jewelry.
- Roll up or don't wear long sleeves.
- Dust protection may be required.
Pre-Operational Safety Checks
- Locate and ensure you are familiar with all machine operations and controls.
- Ensure all guards are fitted, secure and functional. Do not operate if guards are missing or faulty.
- Workpiece must be securely fastened to face plate, chuck or between centers.
- Rotate the workpiece by hand to check clearance between tool rest and bed.
- Ensure the cutting tools are sharp and in good condition.
- Start the dust extraction unit before using the machine.
- Make sure all clamping handles are tight.
Operational Safety Checks
- Adjust speed to suit the diameter of the work and turning operation (IMPORTANT - *never* adjust speed while the lathe is off!)
- Before making adjustments (apart from speed), switch off and bring the machine to a complete standstill.
- Keep the tool rest adjusted close to the work and at the correct height.
- Stop the lathe and remove all tool rests before sanding.
Ending Operations and Cleaning Up
- Switch off the machine when work completed.
- Return all chisels and other tools to racks.
- Leave the machine in a safe, clean and tidy state.
- Sweep or vacuum any wood debris/dust/shavings.
Potential Hazards and Injuries
- Eye injuries from flying debris or defective timber.
- Hair/clothing getting caught in moving machine parts.
- Airborne dust.
- Rough cut the workpiece as close as possible to the finished shape before installing it.
- Check your workpiece for flaws, cracks, knots etc. and test glue joints before mounting the workpiece on machine.
- Use the lowest speed when starting a new workpiece.
- Drive the workpiece into the drive center while the drive center is in the headstock.
- Set the drive center into the workpiece with a soft mallet prior to installing it on the headstock.
- Touch your project by hand while the lathe is running
How To Get Certified
The area host has determined that certifications for this machine should not be viral.
A list of members allowed to certify others will be posted here when the Danger Committee has finish creating a process.
List of Currently Certified Users
|Qualified Member||Trained By||Auth Date|
|Matt Triano||Patrick Grider|
|Sevin Straus||Danger Committee|
|Eric Beauchamp||Danger Committee|
|Erik Wessing||Danger Committee|
|Andrew Camardella||Danger Committee|
|Ray Doeksen||Danger Committee|
|Michael Skilton||Danger Committee|
|Daron Wooding||Andrew Camardella|
|Sam Paris||Andrew Camardella||2016-07-20|
|Donald Wells||Andrew Camardella||2016-07-20|
|McTavish McArdle||Andrew Camardella||2016-07-20|
|An Phan||Andrew Camardella||2016-08-18|
|Matt Keith||Andrew Camardella||2016-08-18|
|Ian Monroe||Andrew Camardella||2016-07-20|
|Les Schier||Sevin Straus||2016-09-01|
|Jon Komperda||Andy Larkin||2016-10-27|
|Clarence Bartenhagen||Sevin Straus||2017-02-01|
|Joe Dowling||Sevin Straus||2017-02-01|
|Crystal Morales||Sevin Straus||2017-03-11|
|Jason Pittman||Sevin Straus||2017-03-11|
The following is a work in progress. https://wiki.pumpingstationone.org/Wood_Lathe_Authorization_Checklist