Line 7: |
Line 7: |
| |arrived = 9/19/14 | | |arrived = 9/19/14 |
| |doesitwork = yes | | |doesitwork = yes |
− | |contact = Dean Anderson | + | |contact = Cold Metals Area Host |
| |where = Cold Metals | | |where = Cold Metals |
| |value = 900 | | |value = 900 |
Line 37: |
Line 37: |
| |- | | |- |
| |} | | |} |
| + | |
| + | == Major Components == |
| + | |
| + | <gallery> |
| + | File:doall-bandsaw-power-plug.jpg|The 4-prong, twist-lock power plug; note the band of purple tape |
| + | File:doall-bandsaw-power-cutoff.jpg|The power cutoff switch, in the 'off' position; the power cutoff needs to be in the 'on' position before the machine will turn on |
| + | File:doall-bandsaw-power-control-panel.jpg|The power control panel; note the on button (upper left), off button (upper right), and key switch (bottom; pictured in the upright, locked position); the key switch needs to be unlocked (turned to the right) before the on button will turn the machine on |
| + | File:doall-bandsaw-cut-parameter-chart.jpg|The cut parameter chart, listing blade speeds & pitch for different materials & thicknesses |
| + | File:doall-bandsaw-speed-dial.jpg|The blade speed dial, which should be set according to the the proper cut parameters found in the chart |
| + | File:doall-bandsaw-gear-selector-knob.jpg|The gear selector knob, in 'high' gear, for coarse control of the blade speed |
| + | File:doall-bandsaw-speed-selector-wheel.jpg|The speed selector wheel, for fine control of the blade speed |
| + | File:doall-bandsaw-table.jpg|The tilting table, in the horizontal position |
| + | File:doall-bandsaw-table-tilt-lock-wheel.jpg|The table tilt lock wheel, in the 'locked' position'; the table's angle can be changed when the wheel is unlocked, and then fixed again in place |
| + | File:doall-bandsaw-blade-guide.jpg|The blade guide; its height above the table is controlled by the positioning wheels |
| + | File:doall-bandsaw-blade-guide-positioning-wheels.jpg|The blade guide positioning wheels: height adjustment (top) and lock (bottom) |
| + | </gallery> |
| | | |
| == Auth/Use Notes == | | == Auth/Use Notes == |
Line 477: |
Line 493: |
| |11/5/15 | | |11/5/15 |
| |- | | |- |
− | |-Caleb Young | + | |Caleb Young |
− | |-Eric Beauchamp | + | |Eric Beauchamp |
| | | | | |
| |- | | |- |
Line 659: |
Line 675: |
| |Mac MacDevitt | | |Mac MacDevitt |
| |Sam Ohlendorf | | |Sam Ohlendorf |
− | 12/20/17 | + | |12/20/17 |
| |- | | |- |
| |[[User:wittnl|Nathan Witt]] | | |[[User:wittnl|Nathan Witt]] |
Line 669: |
Line 685: |
| |1/10/18 | | |1/10/18 |
| |- | | |- |
− | | + | |Amanda Assaley |
| + | |Sam Olendorf |
| + | |1/10/18 |
| + | |- |
| + | |Stephanie Pelzer |
| + | |Sam Olendorf |
| + | |1/10/18 |
| + | |- |
| + | |Chris Eppig |
| + | |Sam Olendorf |
| + | |1/10/18 |
| + | |- |
| + | |Zack Sasnow |
| + | |Sam Olendorf |
| + | |1-26-2018 |
| + | |- |
| + | |Alex Berkowitz |
| + | |Sam Olendorf |
| + | | |
| + | |- |
| + | |Scott Fullman |
| + | |Sam Olendorf |
| + | |2/7/2018 |
| + | |- |
| + | |Arthur Wrobel |
| + | |Sam Olendorf |
| + | |02/07/2018 |
| + | |- |
| + | |Michael Ice |
| + | |Sam Olendorf |
| + | |2/08/18 |
| + | |- |
| + | |Bill Schroeder |
| + | |Sam Olendorf |
| + | |4/18/2018 |
| + | |- |
| + | |Maciej Warchalowski |
| + | |Sam Olendorf |
| + | |6/13/2018 |
| + | |- |
| + | |Jeff Benning |
| + | |Sam Olendorf |
| + | |7/11/2018 |
| + | |- |
| + | |Alex Zhu |
| + | |Sam Olendorf |
| + | |7/25/2018 |
| + | |- |
| + | |Aaron Hale |
| + | |Sam Olendorf |
| + | |8/8/2018 |
| + | |- |
| + | |Ryan Treacy |
| + | |Sam Olendorf |
| + | |9/19/2018 |
| + | |- |
| + | | Jacob Dawson |
| + | | Sam Olendorf |
| + | | 9/19/2018 |
| + | |- |
| + | | Patrick Cook |
| + | | McTavish McArdle |
| + | | 7/23/2019 |
| + | |- |
| + | | Matt Saunders |
| + | | McTavish McArdle |
| + | | 7/23/2019 |
| + | |- |
| + | | Brady Soule |
| + | | Jim Brink |
| + | | 11/20/2017 |
| + | |- |
| + | |} |
| [[Category:Cold Metals]] | | [[Category:Cold Metals]] |