Difference between revisions of "Boice Crane Drill Press"
(Add tool template) |
|||
(24 intermediate revisions by 14 users not shown) | |||
Line 1: | Line 1: | ||
+ | |||
+ | |||
+ | |||
{{Template:EquipmentPage | {{Template:EquipmentPage | ||
|image = boice_crane.jpg | |image = boice_crane.jpg | ||
|owner=PS:One | |owner=PS:One | ||
− | |model=Boice Crane | + | |model=Boice Crane 24103 24" Power Feed |
− | |arrived=January 2015 | + | |arrived=January 2015 |
− | |doesitwork= | + | |serial=23649 |
+ | |doesitwork=yes | ||
|contact=Dean Anderson | |contact=Dean Anderson | ||
− | |where= | + | |where=Cold Metals |
|certification=yes | |certification=yes | ||
|hackable=no | |hackable=no | ||
|value=$600}} | |value=$600}} | ||
+ | |||
+ | =Removal Section= | ||
+ | *What is it? - Boice Crane Drill Press | ||
+ | *Who is sponsoring? - Cold Metals Host - Jim Brink | ||
+ | *Date published to the mailing list and RT- 06/11/2018 | ||
+ | *Asset value - $100 | ||
+ | *Suggested method of removal - Public sale- Craigslist | ||
+ | *Background notes - | ||
+ | *Resolution of removal - | ||
+ | *Approval - | ||
+ | |||
+ | == Specifications == | ||
+ | 8 speed | ||
+ | |||
+ | Gear-head. No belts or Jacobs chuck to slip, which means there is a lot of torque. | ||
+ | |||
+ | Morse #3 taper spindle | ||
+ | |||
+ | Capacity, cast iron 1 1/4" | ||
+ | |||
+ | Drills to center 23" | ||
+ | |||
+ | approximate weight 600 pounds | ||
+ | |||
+ | motor HP 1.5 (high) 1.2 (low) | ||
+ | |||
+ | Spindle speeds (8) 84, ... | ||
+ | |||
+ | == Auth/Use Notes == | ||
+ | |||
+ | These notes are for reference after authorization by a person. | ||
+ | |||
+ | Only use drills and accessories with correct shank taper and tang | ||
+ | |||
+ | Work piece needs secure mounting due to spindle's high torque | ||
+ | |||
+ | No through hole (table designed for coolant), must use vise | ||
+ | |||
+ | No quill stop, must set table or head height to prevent drilling into table | ||
+ | |||
+ | Don't force gear selectors, hand turn spindle as needed to align gears | ||
+ | |||
+ | Gears reverse spindle, must turn power switch to appropriate side for correct spindle rotation direction | ||
+ | |||
+ | Power switch has two speeds to each side | ||
+ | |||
+ | Drill shanks must be firmly seated in taper | ||
+ | |||
+ | To remove drill, lower spindle to expose the slot in the quill, turn the spindle by hand until the quill slot lines up with the spindle slot, insert the #3 drift into the slot with the curved edge facing up, grasp drill, tap drift with hammer | ||
+ | |||
+ | == To-Do == | ||
+ | |||
+ | Clean drill shanks | ||
+ | |||
+ | Mill pocketed vise jaw flat | ||
+ | |||
+ | More clamps matching table T-slots | ||
+ | |||
+ | Improve sketchy quill return mechanism | ||
+ | |||
+ | Adjustable quill stop | ||
+ | |||
+ | Coolant system | ||
+ | |||
+ | == Maintenance == | ||
+ | [[Boice_Crane_Drill_Press_maintenance|Boice_Crane_Drill_Press_maintenance]] | ||
+ | |||
+ | == Equipment == | ||
+ | |||
+ | == References == | ||
+ | |||
+ | == List of Currently Authorized Users == | ||
+ | {| class="wikitable" border="1" | ||
+ | ! Qualified Member | ||
+ | ! Trained By | ||
+ | !Date Trained | ||
+ | |- | ||
+ | |Dean Anderson | ||
+ | |Machine Shop Host Cred | ||
+ | | | ||
+ | |- | ||
+ | |Everett Wilson | ||
+ | |Dean Anderson | ||
+ | |- | ||
+ | |Tom Judd | ||
+ | |Dean Anderson | ||
+ | | | ||
+ | |- | ||
+ | | Todd Allen | ||
+ | | Dean Anderson | ||
+ | |9/15/2015 | ||
+ | | | ||
+ | |- | ||
+ | |Greg Kudlacz | ||
+ | |Todd Allen | ||
+ | |- | ||
+ | |||
+ | |Dafe Hughes | ||
+ | |Todd Allen | ||
+ | |- | ||
+ | |Connor Sullivan | ||
+ | |Tom Judge | ||
+ | |1/22/16 | ||
+ | |- | ||
+ | |Abel Greenwald | ||
+ | |Michael Patton | ||
+ | |- | ||
+ | |Bruce Mace | ||
+ | |Chris Ruhland | ||
+ | |3/7/17 | ||
+ | |- | ||
+ | |Sam Chen | ||
+ | |Chris Ruhland | ||
+ | |3/7/17 | ||
+ | |- | ||
+ | |Michael Ice | ||
+ | |Sam Olendorf | ||
+ | |2/08/18 | ||
+ | |Aaron Hale | ||
+ | |Sam Olendorf | ||
+ | |8/8/2018 | ||
+ | |-} | ||
+ | |||
+ | [[Category:Cold Metals]] |
Latest revision as of 02:46, 30 June 2020
Removal Section
- What is it? - Boice Crane Drill Press
- Who is sponsoring? - Cold Metals Host - Jim Brink
- Date published to the mailing list and RT- 06/11/2018
- Asset value - $100
- Suggested method of removal - Public sale- Craigslist
- Background notes -
- Resolution of removal -
- Approval -
Specifications
8 speed
Gear-head. No belts or Jacobs chuck to slip, which means there is a lot of torque.
Morse #3 taper spindle
Capacity, cast iron 1 1/4"
Drills to center 23"
approximate weight 600 pounds
motor HP 1.5 (high) 1.2 (low)
Spindle speeds (8) 84, ...
Auth/Use Notes
These notes are for reference after authorization by a person.
Only use drills and accessories with correct shank taper and tang
Work piece needs secure mounting due to spindle's high torque
No through hole (table designed for coolant), must use vise
No quill stop, must set table or head height to prevent drilling into table
Don't force gear selectors, hand turn spindle as needed to align gears
Gears reverse spindle, must turn power switch to appropriate side for correct spindle rotation direction
Power switch has two speeds to each side
Drill shanks must be firmly seated in taper
To remove drill, lower spindle to expose the slot in the quill, turn the spindle by hand until the quill slot lines up with the spindle slot, insert the #3 drift into the slot with the curved edge facing up, grasp drill, tap drift with hammer
To-Do
Clean drill shanks
Mill pocketed vise jaw flat
More clamps matching table T-slots
Improve sketchy quill return mechanism
Adjustable quill stop
Coolant system
Maintenance
Boice_Crane_Drill_Press_maintenance
Equipment
References
List of Currently Authorized Users
Qualified Member | Trained By | Date Trained | |||
---|---|---|---|---|---|
Dean Anderson | Machine Shop Host Cred | ||||
Everett Wilson | Dean Anderson | ||||
Tom Judd | Dean Anderson | ||||
Todd Allen | Dean Anderson | 9/15/2015 | |||
Greg Kudlacz | Todd Allen | ||||
Dafe Hughes | Todd Allen | ||||
Connor Sullivan | Tom Judge | 1/22/16 | |||
Abel Greenwald | Michael Patton | ||||
Bruce Mace | Chris Ruhland | 3/7/17 | |||
Sam Chen | Chris Ruhland | 3/7/17 | |||
Michael Ice | Sam Olendorf | 2/08/18 | Aaron Hale | Sam Olendorf | 8/8/2018 |