Difference between revisions of "Gingery Plastic Injection Machine"
Garynhouse (talk | contribs) |
|||
(9 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
<includeonly>[[Category:Equipment]] | <includeonly>[[Category:Equipment]] | ||
{{#ifeq: {{{where|}}} | Removed | [[Category:Removed Equipment]] {{mbox |type=notice |text=This tool is no longer at the space. [[Equipment|Back to list of Equipment]]}} | | {{#ifeq: {{{where|}}} | Removed | [[Category:Removed Equipment]] {{mbox |type=notice |text=This tool is no longer at the space. [[Equipment|Back to list of Equipment]]}} | | ||
− | + | [[Category:Equipment]] | |
{{#if: {{{image|}}} | | [[Category:Photographs_Needed]] }} | {{#if: {{{image|}}} | | [[Category:Photographs_Needed]] }} | ||
{{#switch: {{{doesitwork|}}} | yes | "yes" | Yes | "Yes" | YES | "YES" | y | "y" | Y | "Y" = | [[Category:Broken Equipment]] {{mbox |type=notice |text=This tool is currently broken, please contact the area host for more information. }} }} | {{#switch: {{{doesitwork|}}} | yes | "yes" | Yes | "Yes" | YES | "YES" | y | "y" | Y | "Y" = | [[Category:Broken Equipment]] {{mbox |type=notice |text=This tool is currently broken, please contact the area host for more information. }} }} | ||
{{#if: {{{hostarea|}}} | [[Category:{{{hostarea}}}]] | [[Category:EquipmentPageErrorNoAreahost]] }} | {{#if: {{{hostarea|}}} | [[Category:{{{hostarea}}}]] | [[Category:EquipmentPageErrorNoAreahost]] }} | ||
− | |||
}} | }} | ||
</includeonly> | </includeonly> | ||
− | {{ | + | {{Template:EquipmentPage |
− | | image = | + | |image = GingeryPlasticInjection.JPG |
− | | owner = | + | |owner = PS:One |
− | | | + | |certification = no |
− | | | + | |hackable = no |
− | | | + | |model = |
− | | | + | |serial = |
− | | | + | |arrived = Feb 2017 |
− | | | + | |doesitwork = yes |
− | | | + | |contact = none currently |
− | | | + | |where = Removed |
− | | value = | + | |value = $100 |
− | | hostarea = CNC | + | |hostarea = CNC |
+ | |||
}} | }} | ||
− | |||
− | |||
− | |||
− | |||
− | |||
{{#subobject: | {{#subobject: |
Latest revision as of 02:16, 27 July 2020
This tool is no longer at the space. Back to list of Equipment |
Owner/Loaner | PS:One |
---|---|
Arrival Date | Feb 2017 |
Usability | yes |
Contact | none currently |
Where | Removed |
Authorization Needed | no |
Hackable | no |
Estimated Value | $100 |
Host Area | CNC |
Use
Obviously the heating unit and everything that is attached to the heating unit can get quite hot be careful.
You may want to use a leather glove and pliers while working near the heating unit.
The control unit has a Mypin controller with two switches and a light. The left switch powers the controller. The controller must be on to enable the heating unit. The right switch and the controller power the heating unit. The right switch must be on (up) and the controller will turn on the heating unit until the SV temp is reached.
Capacity
The heating unit cylinder is 1/2" by about 3 1/2", full it will hold about .7 cu in of material.
Below the nozzle the machine has about 4" of room for the mold.
The current nozzle has a taper of 60 degrees so the mold port should have the same taper. The hole in the nozzle is 1/8".
The nozzle is 5/8 11 thread if you want to make your own nozzle.
The heating unit is 300w.
Mypin Temp Controller
The temperature controller displays the current temperature of the heating element (PV) and the set value (SV). Both values are displayed in F. OUT1 = heating control, if lit the heating element is on. AL = alarm1, currently set to 400 degrees F.
To change the SV, Press the </AT key to select the digit you want to modify. Press ^ or v to modify digit. Press SET to confirm.
The above documentation is transcluded from Talk:Gingery Plastic Injection Machine/doc. (edit | history) Please add categories to the /doc subpage. Subpages of this page. |