Difference between revisions of "Boss Laser Settings"
From Pumping Station One
m (→Engraving: add rubber) |
Makelemonade (talk | contribs) |
||
(11 intermediate revisions by 3 users not shown) | |||
Line 8: | Line 8: | ||
===Cutting=== | ===Cutting=== | ||
+ | Cutting power can change based on the state of the laser. Please update with the date if you notice changes. | ||
+ | |||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
Line 15: | Line 17: | ||
! Power (%) | ! Power (%) | ||
! Kerf | ! Kerf | ||
+ | ! Date | ||
|- | |- | ||
| Acrylic | | Acrylic | ||
Line 21: | Line 24: | ||
| 50 | | 50 | ||
| | | | ||
+ | | | ||
+ | |- | ||
+ | | Acrylic | ||
+ | | 1/4" | ||
+ | | 9 | ||
+ | | 80 | ||
+ | | .23mm | ||
+ | | 6/10/2023 | ||
|- | |- | ||
| Plywood | | Plywood | ||
Line 27: | Line 38: | ||
| 80 | | 80 | ||
| | | | ||
+ | |- | ||
+ | | Plywood | ||
+ | | 1/4" | ||
+ | | 55 | ||
+ | | 50 | ||
+ | | | ||
+ | | 5/8/2023 | ||
+ | |- | ||
+ | | MDF Core Plywood (Owl Lumber) | ||
+ | | 5.35 | ||
+ | | 45 | ||
+ | | 70 | ||
+ | | .18mm | ||
+ | | 5/8/2023 | ||
+ | |- | ||
+ | | MDF Core Plywood (Owl Lumber) | ||
+ | | 0.177" | ||
+ | | 25 | ||
+ | | 75 | ||
+ | | 0.0184 | ||
|- | |- | ||
| ABS | | ABS | ||
Line 32: | Line 63: | ||
| 20 | | 20 | ||
| 65 | | 65 | ||
+ | | | ||
| | | | ||
|- | |- | ||
Line 38: | Line 70: | ||
| 150 | | 150 | ||
| 10 | | 10 | ||
+ | | | ||
| | | | ||
|- | |- | ||
Line 44: | Line 77: | ||
| 150 | | 150 | ||
| 25 | | 25 | ||
+ | | | ||
| | | | ||
|- | |- | ||
Line 50: | Line 84: | ||
| 150 | | 150 | ||
| 30 | | 30 | ||
+ | | | ||
| | | | ||
|- | |- | ||
Line 56: | Line 91: | ||
| 30 | | 30 | ||
| 70 | | 70 | ||
+ | | | ||
| | | | ||
|- | |- | ||
Line 63: | Line 99: | ||
| 50 | | 50 | ||
| 0.5mm | | 0.5mm | ||
+ | | | ||
|- | |- | ||
| MDF | | MDF | ||
Line 69: | Line 106: | ||
| 70 | | 70 | ||
| 0.6mm | | 0.6mm | ||
+ | | | ||
+ | |- | ||
+ | | Mylar sheet | ||
+ | | 7.5mil (190 micron) | ||
+ | | 30 to 150 | ||
+ | | 10 | ||
+ | | | ||
|} | |} | ||
Latest revision as of 03:22, 11 June 2023
The below is to help you figure out your settings for your cutting job on the Boss Laser. Please do not be creative with settings unless you know what you're doing, because you can easily set things on fire.
Test Cuts
There are several test cut pieces. These test various power/speed in a pie shape going from 10% to 100%. These are a good starting point.
Known Settings
Known, successfully used settings.
Cutting
Cutting power can change based on the state of the laser. Please update with the date if you notice changes.
Material | Thickness | Speed (mm/second) | Power (%) | Kerf | Date |
---|---|---|---|---|---|
Acrylic | 1/16" | 50 | 50 | ||
Acrylic | 1/4" | 9 | 80 | .23mm | 6/10/2023 |
Plywood | 1/4" | 25? | 80 | ||
Plywood | 1/4" | 55 | 50 | 5/8/2023 | |
MDF Core Plywood (Owl Lumber) | 5.35 | 45 | 70 | .18mm | 5/8/2023 |
MDF Core Plywood (Owl Lumber) | 0.177" | 25 | 75 | 0.0184 | |
ABS | 1/8" | 20 | 65 | ||
Balsa | 1/16" medium density | 150 | 10 | ||
Balsa | 3/32" medium density | 150 | 25 | ||
Balsa | 1/8" medium density | 150 | 30 | ||
Cermark Engraving Brass | 30 | 70 | |||
Masonite | 1/8" | 15 | 50 | 0.5mm | |
MDF | 1/4" | 7.5 | 70 | 0.6mm | |
Mylar sheet | 7.5mil (190 micron) | 30 to 150 | 10 |
Engraving
Material | Depth | Speed (mm/second) | Power (%) |
---|---|---|---|
Masonite | 0.4mm | 100 | 10 |
Masonite | 1mm | 100 | 15 |
Masonite | 1.3mm | 100 | 20 |
Masonite | 1.6mm | 100 | 25 |
Speedycarve (rubber) | ~1mm | 50 | 10 |