Difference between revisions of "Dyna Kiln N100"
(42 intermediate revisions by the same user not shown) | |||
Line 2: | Line 2: | ||
|owner = "PS:One" or link to user page of contact person | |owner = "PS:One" or link to user page of contact person | ||
|hostarea = Small Metals | |hostarea = Small Metals | ||
− | |certification = | + | |certification = yes |
− | |hackable = | + | |hackable = no |
|model = N100 | |model = N100 | ||
|serial = 62356 | |serial = 62356 | ||
Line 11: | Line 11: | ||
|contact = Link to user page of contact person | |contact = Link to user page of contact person | ||
|value = $999 | |value = $999 | ||
− | |image = | + | |image = DynaKilnOverall.jpg |
}} | }} | ||
+ | |||
+ | |||
+ | ==Kiln== | ||
+ | https://en.wikipedia.org/wiki/Kiln | ||
+ | |||
+ | This particular kiln is currently located in the small metals area by the fume hood and induction furnaces. | ||
+ | |||
+ | ==Configuration== | ||
+ | ===Wiring=== | ||
+ | There are 2 power cables required for the kiln. One large diameter cable that connects to the outlet on the red tool box and one smaller diameter cable that goes directly to the wall. See the image below for a block diagram. | ||
+ | |||
+ | The smaller cable connects directly to a mechanical relay within the kiln itself. In order to avoid excessive switching we connect this directly to the wall. | ||
+ | |||
+ | [[File:N100Kiln_FlowDiagram.png| center |Connectivity schematic. ]] | ||
+ | |||
+ | ===Safety Pyro Cone=== | ||
+ | Although the controller works well to stay within the specified temperature profile we also utilize a pyrometric cone (kiln sitter) as an insurance. Make sure that the cone properly supports the safety latch flip (the copper tab that falls when slightly bumped). | ||
+ | |||
+ | |||
+ | |||
+ | Cones - http://media.wix.com/ugd/0c3047_80f20b4c30874c07b971f1b61ac16a03.pdf | ||
+ | Cone Chart - http://media.wix.com/ugd/0c3047_48ee6a1c288c4b1a946dba11de4e9f57.pdf | ||
+ | cone user guide - http://media.wix.com/ugd/0c3047_80f20b4c30874c07b971f1b61ac16a03.pdf | ||
+ | |||
+ | ==Auto Firing== | ||
+ | |||
+ | After properly configuring the cables access to the interface can be found here: http://kilnpi.local:8081/ . | ||
+ | |||
+ | When creating a profile make sure that your ramp rate is <8degF/minute. | ||
+ | |||
+ | [[File:KilnControllerSetup.png| center |Graphical User interface to kiln controller. Address is http://kilnpi.local:8081/ ]] | ||
+ | |||
+ | |||
+ | Github link to raspberry pi setup - https://github.com/jbruce12000/kiln-controller | ||
+ | |||
+ | ===Can't connect to site=== | ||
+ | |||
+ | Raspberry Pi zero can only connect to the 2.4 ghz network which requires your computer to do the same. To configure your machine to the 2.4ghz network you can follow this guide (windows): https://www.windowsdigitals.com/how-to-change-5ghz-to-2-4ghz-in-windows-10/ | ||
+ | |||
+ | |||
+ | |||
+ | ===Kiln Example=== | ||
+ | R&R Accelerated profile | ||
+ | [[File:KilnExample.png| center |Example run near of the accelerated profile. ]] | ||
+ | |||
+ | ==Status== | ||
+ | Kiln works as of 3/24/2022 | ||
+ | |||
+ | ==Authorization== | ||
+ | Authorization is required | ||
+ | |||
+ | ==Safety== | ||
+ | Clear the surrounding area, at least one foot radios, of combustible material, wood, paper and especially aerosol containers. | ||
+ | |||
+ | While firing, before walking away, make sure the hot sign is on the kiln and that bystander have proper warning of extreme heat. | ||
+ | |||
+ | Make sure ceramic wares are cooled below 100 degrees Fahrenheit before handling. | ||
+ | |||
+ | |||
+ | ==Manuals== |
Latest revision as of 00:51, 4 May 2023
Kiln
https://en.wikipedia.org/wiki/Kiln
This particular kiln is currently located in the small metals area by the fume hood and induction furnaces.
Configuration
Wiring
There are 2 power cables required for the kiln. One large diameter cable that connects to the outlet on the red tool box and one smaller diameter cable that goes directly to the wall. See the image below for a block diagram.
The smaller cable connects directly to a mechanical relay within the kiln itself. In order to avoid excessive switching we connect this directly to the wall.
Safety Pyro Cone
Although the controller works well to stay within the specified temperature profile we also utilize a pyrometric cone (kiln sitter) as an insurance. Make sure that the cone properly supports the safety latch flip (the copper tab that falls when slightly bumped).
Cones - http://media.wix.com/ugd/0c3047_80f20b4c30874c07b971f1b61ac16a03.pdf Cone Chart - http://media.wix.com/ugd/0c3047_48ee6a1c288c4b1a946dba11de4e9f57.pdf cone user guide - http://media.wix.com/ugd/0c3047_80f20b4c30874c07b971f1b61ac16a03.pdf
Auto Firing
After properly configuring the cables access to the interface can be found here: http://kilnpi.local:8081/ .
When creating a profile make sure that your ramp rate is <8degF/minute.
Github link to raspberry pi setup - https://github.com/jbruce12000/kiln-controller
Can't connect to site
Raspberry Pi zero can only connect to the 2.4 ghz network which requires your computer to do the same. To configure your machine to the 2.4ghz network you can follow this guide (windows): https://www.windowsdigitals.com/how-to-change-5ghz-to-2-4ghz-in-windows-10/
Kiln Example
R&R Accelerated profile
Status
Kiln works as of 3/24/2022
Authorization
Authorization is required
Safety
Clear the surrounding area, at least one foot radios, of combustible material, wood, paper and especially aerosol containers.
While firing, before walking away, make sure the hot sign is on the kiln and that bystander have proper warning of extreme heat.
Make sure ceramic wares are cooled below 100 degrees Fahrenheit before handling.