Line 1: |
Line 1: |
− | {{Template:EquipmentPage|owner=Adrianna McKinley | + | {{Template:EquipmentPage|owner=PS1 |
− | |model=Forge | + | |model=Deulux 2 Burner Knife Makers Forge |
− | |serial=N/A|arrived=?? | + | |serial=N/A |
| + | |arrived=No |
| |doesitwork= yes | | |doesitwork= yes |
− | |contact= Adrianna McKinley | + | |contact= Tom Judge |
| |where=Hot Metals Area | | |where=Hot Metals Area |
| |certification=yes | | |certification=yes |
− | |hackable=no|value=?? | + | |hackable=no |
| + | |value=$375 |
| |image = None}} | | |image = None}} |
− |
| |
− | The Forge is currently owned by Adrianna and is on loan to the Hot Metals Area along with the following black smithing equipment:
| |
− |
| |
− | Anvil
| |
− | Standing Vice
| |
− | Sledge Hammer
| |
− |
| |
| | | |
| == How to get certified == | | == How to get certified == |
| | | |
− | Adrianna (owner) or Tom Judge (Hot metals area host) can certify you. The following will be covered in the certification:
| + | Certification process is being reviewed, all users will require recertification. |
− | | |
− | ;How to light and turn off the forge.
| |
− | * To turn on go from "fuel to flame"
| |
− | # Connect your propane tank.
| |
− | # Make sure the cutoff switch on top of the burner is turned to off.
| |
− | # Brick up the back and place front brick into the arms on the front of the forge.
| |
− | # Open up the fuel tank completely.
| |
− | # Open up the regulator (green knob near the propane tank end of the fuel line).
| |
− | # Open up the air mix washer to allow more air in.
| |
− | # Have your light lit and ready to go at the side of the forge (also recommend to stand to the side of the forge when lighting).
| |
− | # Slowly open the cutoff.
| |
− | # Once the burner ignites, open the cutoff all the way open.
| |
− | # Run the forge high for a few minutes to warm it up. Then you can close down the air mix to the point where you have a strong torch going (if you have flames rolling up out of the forge you have choked the torch- open up the air mix a little more)
| |
− | | |
− | * To turn off go from "flame to fuel"
| |
− | # Turn the cutoff switch to off.
| |
− | # Close the tank all the way.
| |
− | # Bleed the line by opening the cutoff switch (be careful as a small flame will pop out the air mix washer) until it is empty.
| |
− | # Disconnect your tank and plug the hose into the Hot Metal Area tank (the hose must never be left unplugged in).
| |
| | | |
| == Important Information Regarding the Forge == | | == Important Information Regarding the Forge == |
Line 58: |
Line 34: |
| # Try to use the least amount of air mix you can while not choking the torch. | | # Try to use the least amount of air mix you can while not choking the torch. |
| # If you have a question or something seems off - contact the area host or Adrianna. | | # If you have a question or something seems off - contact the area host or Adrianna. |
| + | |
| + | == List of recomended Certifiers == |
| + | |
| + | * Tom Judge |
| + | |
| | | |
| == List of Currently Certified Users == | | == List of Currently Certified Users == |
Line 65: |
Line 46: |
| ! Trained By | | ! Trained By |
| |- | | |- |
− | |Adrianna McKinley | + | |Tom Judge |
− | |Built Forge | + | |Area Host |
− | |-
| |
− | |[[user:kuroishi|Doorman Dave]]
| |
− | |Adrianna McKinley
| |
− | |-
| |
− | |[[user:Toba|Eric Stein]]
| |
− | |Adrianna McKinley
| |
− | |-
| |
− | |[[user:PatrickSchless|Patrick Schless]]
| |
− | |Adrianna McKinley
| |
| |} | | |} |