Supermax 25x2 Drum Sander
Revision as of 17:51, 22 June 2018 by Dwillm1 (talk | contribs) (→List of Currently Authorized Users)
Owner/Loaner | PS:One |
---|---|
Serial Number | ? |
Make/Model | 25x2 |
Usability | yes |
Contact | Eric Beauchamp |
Where | Wood Shop |
Authorization Needed | yes |
Hackable | no |
Estimated Value | $2700 |
Host Area | Wood Shop |
Notes
- For oily or dense woods (tropical hardwoods, etc), take only very light passes to prevent clogging the sandpaper.
- Use a belt cleaner occasionally to refresh the sandpaper
Safety
This sander features overload detection. If the machine detects too high a load, it will automatically slow down the feed. This saves wear and tear on the machine, but may cause burning of the workpiece if you cut too aggressively.
- The height adjustment on this machine is VERY aggressive. A full turn will raise the table by more than 2mm (a typical cut should be < .5mm). PLEASE USE A MAXIMUM OF 1/8 TURN OF THE HEIGHT WHEEL PER PASS!
- Make your first cuts with a very slow speed (10 or less). Once you are sure the load is OK you can gradually increase the speed on subsequent passes.
- When overload detection kicks in, a red light next to the speed control will turn on. IF YOU SEE THIS LIGHT, PLEASE REDUCE YOUR DEPTH OF CUT AND/OR FEED RATE!
- Like all of our other sanders, sleeves must be above the elbow, and no gloves should be worn. It's pretty easy to get pulled into the rollers.
Outside Links
List of Currently Authorized Users
Qualified Member | Trained By | Date |
---|---|---|
Eric Beauchamp | Danger committee | 6/23/2017 |
Ralph Brendler | Danger committee | 6/23/2017 |
Paul van Lake | Danger committee | 6/23/2017 |
Zack Sasnow | Jason Shanfield | 8/27/17 |
Justin Pestka | Ralph Brendler | 8.30.17 |
Jacob Snyder | Ralph Brendler | 9/7/17 |
James Beck | Ralph Brendler | 9/13/17 |
Ben Starett | Ralph Brendler | 12/14/17 |
Ross Hanchett | Ralph Brendler | 12/14/17 |
Michael Donovan | Ralph Brendler | 12/14/17 |
Jared K | Ralph Brendler | 12/14/17 |
Alex Tomala | Ralph Brendler | 12/21/17 |
Chris Versteeg | Ralph Brandler | 12/28/17 |
Aaron Vander Bee | Ralph Brandler | 1/11/18 |
Ben Farmer | Ralph Brendler | 1/11/18 |
Joseph Crouch | Ralph Brendler | 1/11/18 |
Bradford Smith | Ralph Brendler | 1/11/18 |
Stephanie Pelzer | Ralph Brendler | 1/11/18 |
Amanda Assaley | Ralph Brendler | 1/11/18 |
Chris Eppig | Ralph Brendler | 1/11/18 |
Patrick Smith | Ralph Brendler | 1/11/18 |
Jeff Gershune | Paul VanLake | 1/16/18 |
Bryan Pennington | Ralph Brendler | 1/25/18 |
Michael Ice | Ralph Brendler | 2/08/18 |
Brandon Kennedy | Ralph Brendler | 2/22/18 |
Rolf Scheidt | Ralph Brendler | 2/22/18 |
Dan Mach | Ralph Brendler | 3/8/18 |
Bruce Mace | Ralph Brendler | 3/8/18 |
Ricardo Staudt | Ralph Brendler | 3/8/18 |
Nick Prorok | Ralph Brendler | 3/8/18 |
Paul Graham | Ralph Brendler | 3/22/18 |
Mike Gucciard | Ralph Brendler | 3/22/18 |
Wayne Warren | Ralph Brendler | 3/22/18 |
Adam Hall | Paul V | 3/29/18 |
Bill Schroeder | Ralph Brendler | 4/5/18 |
Mike Wilkin | Ralph Brendler | 4/19/18 |
Alex Lanigan | Ralph Brendler | 4/19/18 |
Jessica Jokhi | Ralph Brendler | 4/19/18 |
Jonathan Frink | Ralph Brendler | 4/19/18 |
Gary Newhouse | Eric Beauchamp | 4/26/18 |
Dave DesRoberts | Paul Van Lake | 4/26/18 |
Jennifer DesRoberts | Paul Van Lake | 4/26/18 |
Wayne Hendryx | Ralph Brendler | 4/19/18 |
Sam Wallinga | Ralph Brendler | 6/14/18 |
Bob Fritz | Ralph Brendler | 6/14/18 |
Nate Myren | Ralph Brendler | 6/14/18 |
Eli Schlossberg | Ralph Brendler | 6/14/18 |
Tyler Works | Ralph Brendler | 6/14/18 |
Daniel Willmott | Paul V | 6/21/18 |