Supermax 25x2 Drum Sander
From Pumping Station One
Revision as of 19:58, 20 July 2018 by Joeday (talk | contribs) (→List of Currently Authorized Users)
Owner/Loaner | PS:One |
---|---|
Serial Number | ? |
Make/Model | 25x2 |
Usability | yes |
Contact | Eric Beauchamp |
Where | Wood Shop |
Authorization Needed | yes |
Hackable | no |
Estimated Value | $2700 |
Host Area | Wood Shop |
Notes
- For oily or dense woods (tropical hardwoods, etc), take only very light passes to prevent clogging the sandpaper.
- Use a belt cleaner occasionally to refresh the sandpaper
Safety
This sander features overload detection. If the machine detects too high a load, it will automatically slow down the feed. This saves wear and tear on the machine, but may cause burning of the workpiece if you cut too aggressively.
- The height adjustment on this machine is VERY aggressive. A full turn will raise the table by more than 2mm (a typical cut should be < .5mm). PLEASE USE A MAXIMUM OF 1/8 TURN OF THE HEIGHT WHEEL PER PASS!
- Make your first cuts with a very slow speed (10 or less). Once you are sure the load is OK you can gradually increase the speed on subsequent passes.
- When overload detection kicks in, a red light next to the speed control will turn on. IF YOU SEE THIS LIGHT, PLEASE REDUCE YOUR DEPTH OF CUT AND/OR FEED RATE!
- Like all of our other sanders, sleeves must be above the elbow, and no gloves should be worn. It's pretty easy to get pulled into the rollers.
Specs
- Sanding Capacity:
- Maximum Width (in): 25
- Minimum Length (in): 3-1/2
- Minimum Thickness (in): 1/32
- Drum Speed: 1740 RPM
- Dust Hood: 1000 CFM recommended
Outside Links
List of Currently Authorized Users
Qualified Member | Trained By | Date |
---|---|---|
Eric Beauchamp | Danger committee | 6/23/2017 |
Ralph Brendler | Danger committee | 6/23/2017 |
Paul van Lake | Danger committee | 6/23/2017 |
Zack Sasnow | Jason Shanfield | 8/27/17 |
Justin Pestka | Ralph Brendler | 8.30.17 |
Jacob Snyder | Ralph Brendler | 9/7/17 |
James Beck | Ralph Brendler | 9/13/17 |
Ben Starett | Ralph Brendler | 12/14/17 |
Ross Hanchett | Ralph Brendler | 12/14/17 |
Michael Donovan | Ralph Brendler | 12/14/17 |
Jared K | Ralph Brendler | 12/14/17 |
Alex Tomala | Ralph Brendler | 12/21/17 |
Chris Versteeg | Ralph Brandler | 12/28/17 |
Aaron Vander Bee | Ralph Brandler | 1/11/18 |
Ben Farmer | Ralph Brendler | 1/11/18 |
Joseph Crouch | Ralph Brendler | 1/11/18 |
Bradford Smith | Ralph Brendler | 1/11/18 |
Stephanie Pelzer | Ralph Brendler | 1/11/18 |
Amanda Assaley | Ralph Brendler | 1/11/18 |
Chris Eppig | Ralph Brendler | 1/11/18 |
Patrick Smith | Ralph Brendler | 1/11/18 |
Jeff Gershune | Paul VanLake | 1/16/18 |
Bryan Pennington | Ralph Brendler | 1/25/18 |
Michael Ice | Ralph Brendler | 2/08/18 |
Brandon Kennedy | Ralph Brendler | 2/22/18 |
Rolf Scheidt | Ralph Brendler | 2/22/18 |
Dan Mach | Ralph Brendler | 3/8/18 |
Bruce Mace | Ralph Brendler | 3/8/18 |
Ricardo Staudt | Ralph Brendler | 3/8/18 |
Nick Prorok | Ralph Brendler | 3/8/18 |
Paul Graham | Ralph Brendler | 3/22/18 |
Mike Gucciard | Ralph Brendler | 3/22/18 |
Wayne Warren | Ralph Brendler | 3/22/18 |
Adam Hall | Paul V | 3/29/18 |
Bill Schroeder | Ralph Brendler | 4/5/18 |
Mike Wilkin | Ralph Brendler | 4/19/18 |
Alex Lanigan | Ralph Brendler | 4/19/18 |
Jessica Jokhi | Ralph Brendler | 4/19/18 |
Jonathan Frink | Ralph Brendler | 4/19/18 |
Gary Newhouse | Ralph Brendler | 4/26/18 |
Dave DesRoberts | Paul Van Lake | 4/26/18 |
Jennifer DesRoberts | Paul Van Lake | 4/26/18 |
Wayne Hendryx | Ralph Brendler | 4/19/18 |
Kirsten Landmark Masih | Ralph Brendler | 6/07/18 |
Sam Wallinga | Ralph Brendler | 6/14/18 |
Bob Fritz | Ralph Brendler | 6/14/18 |
Nate Myren | Ralph Brendler | 6/14/18 |
Eli Schlossberg | Ralph Brendler | 6/14/18 |
Tyler Works | Ralph Brendler | 6/14/18 |
Daniel Willmott | Paul V | 6/21/18 |
Bruce Levin | Paul V4 | |
Joe Day | Paul V | 7/05/18 |
Mike Yacobucci | Ralph Brendler | 7/12/18 |