Line 6: |
Line 6: |
| |serial=1456658 | | |serial=1456658 |
| |doesitwork=yes | | |doesitwork=yes |
− | |contact=Dean Anderson
| |
| |where=Cold Metals | | |where=Cold Metals |
| + | |hostarea=Cold Metals |
| |certification=yes | | |certification=yes |
| |hackable=no | | |hackable=no |
Line 29: |
Line 29: |
| | | |
| Weight: 400 pounds | | Weight: 400 pounds |
| + | |
| + | == Major Components == |
| + | |
| + | <gallery> |
| + | File:rockwell-drill-press-control-boxes.jpg|The VFD (top) and spindle control box (bottom) |
| + | File:rockwell-drill-press-main-power-switch.jpg|The main power switch, located on the back of the spindle control box, in the 'off' position; this needs to be 'on' for the VFD to receive power |
| + | File:rockwell-drill-press-spindle-control-panel.jpg|The spindle control panel: the RPM readout (top; unpowered), RPM control knob (middle), and spindle power switch (bottom; off); the spindle power switch needs to be 'on' before the motor will turn the spindle |
| + | File:rockwell-drill-press-emergency-stop.jpg|The emergency stop button, in the 'off' (pushed-in) position; needs to be rotated to the left to pop out into the 'on' position; the e-stop should be disengaged before the spindle power switch is toggled 'on' |
| + | File:rockwell-drill-press-spindle-chuck.jpg|The spindle and the drill chuck which is more-or-less permanently inserted into it |
| + | File:rockwell-drill-press-chuck-key.jpg|The chuck key and retaining magnet |
| + | File:rockwell-drill-press-feed-lever.jpg|The feed lever, used to lower and raise the spindle |
| + | File:rockwell-drill-press-depth-stop.jpg|The adjustable (by screwing it up or down) depth stop attached to the spindle, used to limit its downward travel |
| + | File:rockwell-drill-press-table.jpg|The table, on which the work is placed or fixed |
| + | File:rockwell-drill-press-table-height-handle.jpg|The handle used to adjust the height of the table; the table height lock needs to be disengaged before adjustment |
| + | File:rockwell-drill-press-table-height-lock.jpg|The lever used to lock the height of the table, in the downward, 'locked' position |
| + | </gallery> |
| | | |
| == Auth/Use Notes == | | == Auth/Use Notes == |
Line 40: |
Line 56: |
| These notes are for reference after authorization by a person. | | These notes are for reference after authorization by a person. |
| | | |
− | The spindle switch must be 'off' and the e-stop (big red button) must be in the out position (twist the button counter clockwise) before the spindle can be turned on. | + | The spindle switch must be 'off' and the e-stop (big red button) must be in the out position (twist the button counter clockwise) before the spindle can be turned on. Note-- If the VFD shows an E5 code check the e switch, it needs to be in the on (extended) position. |
| | | |
| Authorizations from the old DoAll drill press carry over to this machine. | | Authorizations from the old DoAll drill press carry over to this machine. |
Line 150: |
Line 166: |
| |1/10/18 | | |1/10/18 |
| |- | | |- |
− |
| |
| |Chris Eppig | | |Chris Eppig |
| |Sam Olendorf | | |Sam Olendorf |
Line 157: |
Line 172: |
| |Zack Sasnow | | |Zack Sasnow |
| |Sam Olendorf | | |Sam Olendorf |
− | |2018-1-26-2018 | + | |1-26-2018 |
| |- | | |- |
− | | + | |Bill Schroeder |
| + | |Sam Olendorf |
| + | |4/18/2018 |
| + | |- |
| + | |Gary Newhouse |
| + | |Eric Beauchamp |
| + | |4/26/18 |
| + | |- |
| + | |Maciej Warchalowski |
| + | |Sam Olendorf |
| + | |6/13/18 |
| + | |- |
| + | |Alex Zhu |
| + | |Sam Olendorf |
| + | |7/25/18 |
| + | |- |
| + | |Malindima Sampa |
| + | |McTavish McArdle |
| + | |1/7/2020 |
| + | |- |
| + | |Michelle deLeon |
| + | |McTavish McArdle |
| + | |02/04/20} |
| + | |- |
| + | |Corwin Kline |
| + | |McTavish McArdle |
| + | |02/04/2020 |
| + | |-} |
| [[Category:Cold Metals]] | | [[Category:Cold Metals]] |