3,430
edits
Changes
Jump to navigation
Jump to search
mLine 1:
Line 1: − [[Category:Fabrication]] − Line 22:
Line 20: − + Line 29:
Line 27: − + − + − + − + − + − + Line 109:
Line 107: + +
Robot: Cosmetic changes
{{Template:EquipmentPage
{{Template:EquipmentPage
|owner = PS:One
|owner = PS:One
=== Windows Drivers ===
=== Windows Drivers ===
Windows users will need to install drivers.
Windows users will need to install drivers.
For everyone else, It Just Works™. Where everyone = Linux and OSX users.
For everyone else, It Just Works™. Where everyone = Linux and OSX users.
=== Usable Print Area ===
=== Usable Print Area ===
=== Host Software ===
=== Host Software ===
Users of Linux, Windows, OSX will need to install the following software:
Users of Linux, Windows, OSX will need to install the following software:
*[https://github.com/kliment/Printrun#getting-printrun Pronterface] - or [http://www.repetier.com/download/ Repeteir-Host] for manual operation of the printer as well as for starting print jobs
* [https://github.com/kliment/Printrun#getting-printrun Pronterface] - or [http://www.repetier.com/download/ Repeteir-Host] for manual operation of the printer as well as for starting print jobs
*[http://slic3r.org/download Slic3r] - for creating gcode (print jobs) from 3D models
* [http://slic3r.org/download Slic3r] - for creating gcode (print jobs) from 3D models
*Additionally, Lulzbot provides a [http://downloads.lulzbot.com/lulzbot/AO-100/software/2012-Q2/configs/slic3r/point5mm.ini slic3r config file] for the AO-100 LulzBot.
* Additionally, Lulzbot provides a [http://downloads.lulzbot.com/lulzbot/AO-100/software/2012-Q2/configs/slic3r/point5mm.ini slic3r config file] for the AO-100 LulzBot.
=== Suggested Settings ===
=== Suggested Settings ===
Lulzbot's slic3r config has the infill density set at 0.75. Resulting prints are very sturdy as a result, but the filament consumption and print time go up because of this. It is recommended to turn it down to 0.15 or 0.25, and to increase the number of infill shells. Doing so should have a similar surface quality, but produce a print with significantly less mass.
Lulzbot's slic3r config has the infill density set at 0.75. Resulting prints are very sturdy as a result, but the filament consumption and print time go up because of this. It is recommended to turn it down to 0.15 or 0.25, and to increase the number of infill shells. Doing so should have a similar surface quality, but produce a print with significantly less mass.
=== Other Resources ===
=== Other Resources ===
[http://downloads.lulzbot.com/lulzbot/AO-100/documentation/2012Q3/ The manual is available online]. A printed form of it can be found near the printer. The manual explains how to operate the printer. Read it =)
[http://downloads.lulzbot.com/lulzbot/AO-100/documentation/2012Q3/ The manual is available online]. A printed form of it can be found near the printer. The manual explains how to operate the printer. Read it =)
=== Filament ===
=== Filament ===
The printer is currently configured for 3mm ABS plastic. Only use this kind of plastic. Until Aeva has a chance to upgrade the extruder, PLA can damage the hot end. Additionally, the Makerbot is not configured for 3mm ABS, and so the filament for these respective printers is currently not interchangeable.
The printer is currently configured for 3mm ABS plastic. Only use this kind of plastic. Until Aeva has a chance to upgrade the extruder, PLA can damage the hot end. Additionally, the Makerbot is not configured for 3mm ABS, and so the filament for these respective printers is currently not interchangeable.
=== Find Something to Print ===
=== Find Something to Print ===
|Elizabeth Koprucki
|Elizabeth Koprucki
|-}
|-}
[[Category:Fabrication]]