7
edits
Changes
Jump to navigation
Jump to search
Line 1:
Line 1: − + Line 6:
Line 6: − |contact=Dean Anderson + Line 29:
Line 29: + + + + + + + + + + + + + + + + + + + + + + Line 64:
Line 86: − + − + − + Line 74:
Line 96: + Line 101:
Line 124: − + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + −
→List of Currently Authorized Users
{{Template:EquipmentPage
{{Template:EquipmentPage
|image =
|image = rockwell-drill-press.jpg
|owner=PS:One
|owner=PS:One
|model=Rockwell 17-600 17" Drill Press
|model=Rockwell 17-600 17" Drill Press
|serial=1456658
|serial=1456658
|doesitwork=yes
|doesitwork=yes
|where=Cold Metals
|where=Cold Metals
|hostarea=Cold Metals
|certification=yes
|certification=yes
|hackable=no
|hackable=no
Weight: 400 pounds
Weight: 400 pounds
== Major Components ==
<gallery>
File:rockwell-drill-press-control-boxes.jpg|The VFD (top) and spindle control box (bottom)
File:rockwell-drill-press-main-power-switch.jpg|The main power switch, located on the back of the spindle control box, in the 'off' position; this needs to be 'on' for the VFD to receive power
File:rockwell-drill-press-spindle-control-panel.jpg|The spindle control panel: the RPM readout (top; unpowered), RPM control knob (middle), and spindle power switch (bottom; off); the spindle power switch needs to be 'on' before the motor will turn the spindle
File:rockwell-drill-press-emergency-stop.jpg|The emergency stop button, in the 'off' (pushed-in) position; needs to be rotated to the left to pop out into the 'on' position; the e-stop should be disengaged before the spindle power switch is toggled 'on'
File:rockwell-drill-press-spindle-chuck.jpg|The spindle and the drill chuck which is more-or-less permanently inserted into it
File:rockwell-drill-press-chuck-key.jpg|The chuck key and retaining magnet
File:rockwell-drill-press-feed-lever.jpg|The feed lever, used to lower and raise the spindle
File:rockwell-drill-press-depth-stop.jpg|The adjustable (by screwing it up or down) depth stop attached to the spindle, used to limit its downward travel
File:rockwell-drill-press-table.jpg|The table, on which the work is placed or fixed
File:rockwell-drill-press-table-height-handle.jpg|The handle used to adjust the height of the table; the table height lock needs to be disengaged before adjustment
File:rockwell-drill-press-table-height-lock.jpg|The lever used to lock the height of the table, in the downward, 'locked' position
</gallery>
== Auth/Use Notes ==
== Auth/Use Notes ==
Recommended Drill Protocol:
#A full set of fractional, number and letter drills are available in a index case next to the drill. Use a drill from this case if one is available and usable. If a drill is unusable repair it or put it into the discarded drill tray.
#If no drill is available or usable in the index case take one from the cabinets.
#When you are through with the drill replace it into the index case.
#With this procedure users can be assured that drills from the cabinet are new and drills from the index case may be OK but should be checked.
These notes are for reference after authorization by a person.
These notes are for reference after authorization by a person.
== List of Currently Authorized Users ==
== List of Currently Authorized Users ==
{| class="wikitable" border="1"
{| class="wikitable" border="1"
! Qualified Member
! Qualified Member
! Trained By
! Trained By
!Date Trained
! Date
|-
|-
|Dean Anderson
|Dean Anderson
|Everett Wilson
|Everett Wilson
|Dean Anderson
|Dean Anderson
|
|-
|-
|Bruce Mace
|Bruce Mace
|Arjun Sharma
|Arjun Sharma
|Tom Judge
|Tom Judge
|8.10.17
|8/10/17
|-
|[[User:Ekaj|Jacob Snyder]]
|Sam Olendorf
|9/13/17
|-
|Sean Nixon
|Sam Olendorf
|9/27/17
|-
|Mateusz Pec
|Sam Olendorf
|9/27/17
|-
|[[User:Bobbyh|Bobby Huggins]]
|Sam Olendorf
|11/15/17
|-
|Ryan Himmelblau
|Sam Olendorf
|11/15/17
|-
|Mac MacDevitt
|Sam Olendorf
|12/20/17
|-
|[[User:wittnl|Nathan Witt]]
|Sam Olendorf
|11/29/17
|-
|Aaron Vander Bee
|Sam Olendorf
|1/10/18
|-
|Amanda Assaley
|Sam Olendorf
|1/10/18
|-
|Stephanie Pelzer
|Sam Olendorf
|1/10/18
|-
|Chris Eppig
|Sam Olendorf
|1/10/18
|-
|Zack Sasnow
|Sam Olendorf
|1-26-2018
|-
|Bill Schroeder
|Sam Olendorf
|4/18/2018
|-
|Gary Newhouse
|Eric Beauchamp
|4/26/18
|-
|Maciej Warchalowski
|Sam Olendorf
|6/13/18
|-
|Alex Zhu
|Sam Olendorf
|7/25/18
|-
|Michelle deLeon
|McTavish McArdle
|02/04/20}
|-
|Corwin Kline
|McTavish McArdle
|02/04/2020
|-}
|-}
[[Category:Cold Metals]]
[[Category:Cold Metals]]