533
edits
Changes
Jump to navigation
Jump to search
Line 1:
Line 1: − + Line 6:
Line 6: − |contact=Dean Anderson + Line 29:
Line 29: + + + + + + + + + + + + + + + + Line 40:
Line 56: − + Line 150:
Line 166: − + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +
→Auth/Use Notes
{{Template:EquipmentPage
{{Template:EquipmentPage
|image =
|image = rockwell-drill-press.jpg
|owner=PS:One
|owner=PS:One
|model=Rockwell 17-600 17" Drill Press
|model=Rockwell 17-600 17" Drill Press
|serial=1456658
|serial=1456658
|doesitwork=yes
|doesitwork=yes
|where=Cold Metals
|where=Cold Metals
|hostarea=Cold Metals
|certification=yes
|certification=yes
|hackable=no
|hackable=no
Weight: 400 pounds
Weight: 400 pounds
== Major Components ==
<gallery>
File:rockwell-drill-press-control-boxes.jpg|The VFD (top) and spindle control box (bottom)
File:rockwell-drill-press-main-power-switch.jpg|The main power switch, located on the back of the spindle control box, in the 'off' position; this needs to be 'on' for the VFD to receive power
File:rockwell-drill-press-spindle-control-panel.jpg|The spindle control panel: the RPM readout (top; unpowered), RPM control knob (middle), and spindle power switch (bottom; off); the spindle power switch needs to be 'on' before the motor will turn the spindle
File:rockwell-drill-press-emergency-stop.jpg|The emergency stop button, in the 'off' (pushed-in) position; needs to be rotated to the left to pop out into the 'on' position; the e-stop should be disengaged before the spindle power switch is toggled 'on'
File:rockwell-drill-press-spindle-chuck.jpg|The spindle and the drill chuck which is more-or-less permanently inserted into it
File:rockwell-drill-press-chuck-key.jpg|The chuck key and retaining magnet
File:rockwell-drill-press-feed-lever.jpg|The feed lever, used to lower and raise the spindle
File:rockwell-drill-press-depth-stop.jpg|The adjustable (by screwing it up or down) depth stop attached to the spindle, used to limit its downward travel
File:rockwell-drill-press-table.jpg|The table, on which the work is placed or fixed
File:rockwell-drill-press-table-height-handle.jpg|The handle used to adjust the height of the table; the table height lock needs to be disengaged before adjustment
File:rockwell-drill-press-table-height-lock.jpg|The lever used to lock the height of the table, in the downward, 'locked' position
</gallery>
== Auth/Use Notes ==
== Auth/Use Notes ==
These notes are for reference after authorization by a person.
These notes are for reference after authorization by a person.
The spindle switch must be 'off' and the e-stop (big red button) must be in the out position (twist the button counter clockwise) before the spindle can be turned on.
The spindle switch must be 'off' and the e-stop (big red button) must be in the out position (twist the button counter clockwise) before the spindle can be turned on. Note-- If the VFD shows an E5 code check the e switch, it needs to be in the on (extended) position.
Authorizations from the old DoAll drill press carry over to this machine.
Authorizations from the old DoAll drill press carry over to this machine.
|1/10/18
|1/10/18
|-
|-
|Chris Eppig
|Chris Eppig
|Sam Olendorf
|Sam Olendorf
|1/10/18
|1/10/18
|-
|-
|Zack Sasnow
|Sam Olendorf
|1-26-2018
|-
|Bill Schroeder
|Sam Olendorf
|4/18/2018
|-
|Gary Newhouse
|Eric Beauchamp
|4/26/18
|-
|Maciej Warchalowski
|Sam Olendorf
|6/13/18
|-
|Alex Zhu
|Sam Olendorf
|7/25/18
|-
|Malindima Sampa
|McTavish McArdle
|1/7/2020
|-
|Michelle deLeon
|McTavish McArdle
|02/04/20}
|-
|Corwin Kline
|McTavish McArdle
|02/04/2020
|-}
[[Category:Cold Metals]]
[[Category:Cold Metals]]