Line 1: |
Line 1: |
| {{Template:EquipmentPage | | {{Template:EquipmentPage |
− | |image = boice_crane.jpg | + | |image = |
| |owner=PS:One | | |owner=PS:One |
− | |model=Boice Crane 24103 24" Power Feed | + | |model=Rockwell 17-600 17" Drill Press |
− | |arrived=January 2015 | + | |arrived=December 2016 |
− | |serial=23649 | + | |serial=1456658 |
| |doesitwork=yes | | |doesitwork=yes |
| |contact=Dean Anderson | | |contact=Dean Anderson |
Line 10: |
Line 10: |
| |certification=yes | | |certification=yes |
| |hackable=no | | |hackable=no |
− | |value=$600}} | + | |value=$500}} |
| | | |
| | | |
| == Specifications == | | == Specifications == |
− | 8 speed
| + | 17" capacity (from the center of the spindle to the column). |
| | | |
− | Gear-head. No belts or Jacobs chuck to slip, which means there is a lot of torque.
| + | VFD controlled 3 phase motor. Continuously variable spindle speed from 250-??. |
| | | |
− | Morse #3 taper spindle | + | Morse #2 taper spindle |
| | | |
− | Capacity, cast iron 1 1/4" | + | Capacity, mild steel 1/2" |
| | | |
− | Drills to center 23" | + | Drills to center 17" |
| | | |
− | approximate weight 600 pounds | + | approximate weight ?? pounds |
| | | |
− | motor HP 1.5 (high) 1.2 (low) | + | motor HP 1 |
− | | |
− | Spindle speeds (8) 84, ...
| |
| | | |
| + | |
| == Auth/Use Notes == | | == Auth/Use Notes == |
| | | |
Line 36: |
Line 35: |
| Only use drills and accessories with correct shank taper and tang | | Only use drills and accessories with correct shank taper and tang |
| | | |
− | Work piece needs secure mounting due to spindle's high torque
| + | |
− | | |
− | No through hole (table designed for coolant), must use vise
| |
− | | |
− | No quill stop, must set table or head height to prevent drilling into table
| |
− | | |
− | Don't force gear selectors, hand turn spindle as needed to align gears
| |
− | | |
− | Gears reverse spindle, must turn power switch to appropriate side for correct spindle rotation direction
| |
− | | |
− | Power switch has two speeds to each side
| |
− | | |
− | Drill shanks must be firmly seated in taper
| |
− | | |
− | To remove drill, lower spindle to expose the slot in the quill, turn the spindle by hand until the quill slot lines up with the spindle slot, insert the #3 drift into the slot with the curved edge facing up, grasp drill, tap drift with hammer
| |
| | | |
| + | |
| == To-Do == | | == To-Do == |
| | | |
− | Clean drill shanks
| + | |
− | | |
− | Mill pocketed vise jaw flat
| |
− | | |
− | More clamps matching table T-slots
| |
− | | |
− | Improve sketchy quill return mechanism
| |
− | | |
− | Adjustable quill stop
| |
− | | |
− | Coolant system
| |
| | | |
| == Maintenance == | | == Maintenance == |
Line 79: |
Line 55: |
| |- | | |- |
| |Dean Anderson | | |Dean Anderson |
− | |Machine Shop Host Cred | + | | |
| | | | | |
| |- | | |- |
| |Everett Wilson | | |Everett Wilson |
| |Dean Anderson | | |Dean Anderson |
− | |-
| |
− | |Tom Judd
| |
− | |Dean Anderson
| |
− | |
| |
− | |-
| |
− | | Todd Allen
| |
− | | Dean Anderson
| |
− | |9/15/2015
| |
− | |
| |
− | |-
| |
− | |Greg Kudlacz
| |
− | |Todd Allen
| |
− | |-
| |
− |
| |
− | |Dafe Hughes
| |
− | |Todd Allen
| |
− | |-
| |
− | |Connor Sullivan
| |
− | |Tom Judge
| |
− | |1/22/16
| |
− | |-
| |
− | |Abel Greenwald
| |
− | |Michael Patton
| |
| |- | | |- |
| |Bruce Mace | | |Bruce Mace |