1,580
edits
Changes
From Pumping Station One
Sawstop Industrial Table Saw (view source)
Revision as of 20:09, 14 October 2022
, 20:09, 14 October 2022→Sacrificial Fence
|hackable = NO
|hackable = NO
|model = Model ICS 73230 7.5HP 220V
|model = Model ICS 73230 7.5HP 220V
|serial = Pxxxxxxxx
|serial = SI 193301732
|arrived = 1/110/2020
|arrived = 1/110/2020
|doesitwork = not yet
|doesitwork = yes
|contact = Wood Shop Area Host
|contact = Wood Shop Area Host
|where = Wood Shop
|where = Wood Shop
= Authorization for this tool by authorized proctors only =
= Authorization for this tool by authorized proctors only. Members not previously Authorized must take the CANVAS course at https://canvas.pumpingstationone.org/courses/40 =
== Authorized Proctors ==
== Authorized Proctors ==
{| class="wikitable" border="1"
{| class="wikitable" border="1"
|Ralph Brendler
|Ralph Brendler
|-
|-
|Paul VanLake
|Tim Kaye
|-
|-
|Michelle DeLeon
|Joe Staffa
|}
|}
== Status ==
== Status ==
this very heavy duty version of the SawStop is currently being set up
July 17 2020. User reported kickback and then saw stopped and won’t restart. Woodshop team has tested breakers and safety lockout mechanisms. Troubleshooting continues.
August 6. After replacing parts on saw, final part of fix was replacing breaker in panel. Circuit overloaded lugs but did not trip breaker.
Sept 2021. Fence guide ruler shredded. Replaced gn
Sept 24 2021. Report that the blade stopped motor stopped and smoke was billowing from motor box and ductwork. After a long rest, it was tested and no fault found. Stress tested 9/26 and put back into service. Gn
March -may 2022. Long series of machine errors ranging from false brake firings to blade rot error code to no power at controller. Lots of troubleshooting and blade brake replacements. Also replaces start cap.per sawstop direction. Worked short while then happened again. On
may 19, EB replaced run capacitor. Hoping that this works.
Thruout may and June 2022 we have replaced nearly every electrical /electronic part as well as fixing an issue in the breaker panel. EricB in communications with sawstop. —gn
6/30/2022 gn and DE discussed another troubleshooting approach
7/7/2022 eric replaced several remaining electronic parts. it seems to be working now.
this very heavy duty version of the SawStop was installed January 2020
= Rules =
= Rules =
SawStop saws support 8″ dado sets only. The optional dado brake cartridge must be used for dado cuts. It has a larger brake pawl designed to stop the multiple blades in a dado set. In addition, you will also need to use a zero-clearance insert specifically for the dado set.
SawStop saws support 8″ dado sets only. The optional dado brake cartridge must be used for dado cuts. It has a larger brake pawl designed to stop the multiple blades in a dado set. In addition, you will also need to use a zero-clearance insert specifically for the dado set.
The dado stack is stored in the center metal cabinet under the hand tools bench. It’s labeled. The dado brake should also be stored there tho it sometimes appears in “nightstand 2” with extra splitters etc.
The zero clearance insert is with other inserts and feather boards and pushers in small “nightstand” under right side table extension.
http://www.rockler.com/sawstop-dado-brake-cartridge-for-cns-table-saws
http://www.rockler.com/sawstop-dado-brake-cartridge-for-cns-table-saws
The sacrificial fence is placed on top of the standard table saw rip fence and secured with the screws on the back side. Ensure that the fence is square to the table while tightening the set screws, and that the fence is flush with the front of the rip fence. Then, slide the fence over top of the dado stack, adjusting the fence for the desired rebate width. Adjust the blade height for the desired depth of rebate.
The sacrificial fence is placed on top of the standard table saw rip fence and secured with the screws on the back side. Ensure that the fence is square to the table while tightening the set screws, and that the fence is flush with the front of the rip fence. Then, slide the fence over top of the dado stack, adjusting the fence for the desired rebate width. Adjust the blade height for the desired depth of rebate.
It is stored in the outfeed table. See the table saw jigs page.
See: https://www.youtube.com/watch?v=JYqvwlbm6B0 beginning at minute 8 for a demonstration of how the sacrificial fence works.
See: https://www.youtube.com/watch?v=JYqvwlbm6B0 beginning at minute 8 for a demonstration of how the sacrificial fence works.
[https://wiki.pumpingstationone.org/Tablesaw_jigs_and_sleds#sacrificial_fences sleds n jigs n such]
== Blade Brake ==
== Blade Brake ==
== Training Links ==
== Training Links ==
Manual download [https://www.sawstop.com/images/uploads/manuals/Manual_ICS_2.pdf]
Manual download [https://www.sawstop.com/images/uploads/manuals/Manual_ICS_2.pdf]
== Maintenance ==
== Maintenance ==
* [http://web.archive.org/web/20130224091815/http://www.woodworkersjournal.com/Main/Articles/Table_Saw_Maintenance_Skill_Builder_Power_Tool_Tun_8197.aspx Table Saw Maintenance]
* [http://web.archive.org/web/20130224091815/http://www.woodworkersjournal.com/Main/Articles/Table_Saw_Maintenance_Skill_Builder_Power_Tool_Tun_8197.aspx Table Saw Maintenance]
* [[SawStop Table Saw maintenance|maintenance page]]
* [[SawStop Table Saw maintenance|maintenance page]]
* Power beaker Switch is in hot metals shop panel.
