Line 16: |
Line 16: |
| | | |
| == Status == | | == Status == |
− | * 6/27/2019 Universal was repaired by Scientific Spectrum Midwest to full functionality. Need to fix air supply before the Universal is put back into service. See required parts needed [[Media:Air_Assist_Parts_Assembly.doc ]] See [[Media:2_Table_Calibration_Platform_Lasers.pdf]] and [[Media:5_Cleaning_and_Maintenance.pdf]] for maintenance. | + | * 6/27/2019 Universal was repaired by Scientific Spectrum Midwest to full functionality. Need to fix air supply before the Universal is put back into service. See required parts needed [[Media:Air_Assist_Parts_Assembly.doc ]] See [[Media:2_Table_Calibration_Platform_Lasers.pdf]] and [[Media:5_Cleaning_and_Maintenance.pdf]] for maintenance. If you need to get familiar with the universal, please checkout out [[Media:6_Keep_these_thoughts_in_mind_when_creating_a_drawing.pdf]] and [[Media:7 Laser procedure.pdf]] |
| * 5/19/2019 Universal laser is not working. Ask the Area Host at [email protected] for more information. | | * 5/19/2019 Universal laser is not working. Ask the Area Host at [email protected] for more information. |
| * 04/1/2019 Back Up And running, Check Google Group for more details | | * 04/1/2019 Back Up And running, Check Google Group for more details |
Line 39: |
Line 39: |
| * [[Media:Universal PLS6.150D user guide.pdf|Universal Laser PLS6.150D User Manual]] | | * [[Media:Universal PLS6.150D user guide.pdf|Universal Laser PLS6.150D User Manual]] |
| * [https://docs.google.com/spreadsheets/d/11G3HMFiu8aKGAu2Eg_p9LCSjKiajoUDsriVcqi_09hU/pub?output=html#| Materials Settings Reference] | | * [https://docs.google.com/spreadsheets/d/11G3HMFiu8aKGAu2Eg_p9LCSjKiajoUDsriVcqi_09hU/pub?output=html#| Materials Settings Reference] |
− | * [[Media:6 Keep these thoughts in mind when creating a drawing.pdf]] | + | * [[Media:6_Keep_these_thoughts_in_mind_when_creating_a_drawing.pdf]] |
− | * [[Media:7_Laser_procedure.pdf]] | + | * [[Media:7 Laser procedure.pdf]] |
| | | |
| == About == | | == About == |
Line 51: |
Line 51: |
| | | |
| == Procedures == | | == Procedures == |
− |
| |
− | === Maintenance ===
| |
− | [https://wiki.pumpingstationone.org/Universal_Maintenance Universal Maintenance]
| |
− | * [[Media:2_Table_Calibration_Platform_Lasers.pdf]]
| |
− | * [[Media:5_Cleaning_and_Maintenance.pdf]]
| |
| | | |
| === Setting Up Your Computer=== | | === Setting Up Your Computer=== |
Line 74: |
Line 69: |
| === Exhaust === | | === Exhaust === |
| * Turn on the Exhaust Fan by flipping the switch on the gray box to the left of the Boss Laser. | | * Turn on the Exhaust Fan by flipping the switch on the gray box to the left of the Boss Laser. |
| + | * Make sure the BLAST GATE is open. |
| + | * It is always good practice to open the Make-up Air Window to allow fresh air to circulate while running a job. |
| | | |
| === Powering On Machine === | | === Powering On Machine === |
Line 79: |
Line 76: |
| | | |
| == Running your job == | | == Running your job == |
− | *Use the printer driver and Universal Control Panel (UCP) to send data to the laser. | + | * Use the printer driver and Universal Control Panel (UCP) to send data to the laser. |
− | *The printer driver is discussed from page 39-57 of the manual, and on page 58-62, the UCP is explained. | + | * The printer driver is discussed from page 39-57 of the manual, and on page 58-62, the UCP is explained. |
− | *https://wiki.pumpingstationone.org/images/Universal_PLS6.150D_user_guide.pdf | + | * https://wiki.pumpingstationone.org/images/Universal_PLS6.150D_user_guide.pdf |
| + | * ALLOW AT LEAST 30 SECONDS TO ELAPSE BEFORE LIFTING THE LID AFTER A JOB. |
| | | |
| === Powering Off Machine === | | === Powering Off Machine === |
− | * Allow the Exhaust & Air Assist to run for approximately 10-15 after completing a job. (DO NOT CYCLE THE EXHAUST SYSTEM RAPIDLY). | + | * Allow the Exhaust & Air Assist to run for approximately 10-15 min. after completing a job. (DO NOT CYCLE THE EXHAUST SYSTEM RAPIDLY). |
| * Turn off the Exhaust & Air Assist FIRST | | * Turn off the Exhaust & Air Assist FIRST |
| * Power down the machine | | * Power down the machine |
Line 137: |
Line 135: |
| |} | | |} |
| | | |
| + | |
| + | == Maintenance == |
| + | |
| + | Please note that ONLY authorized maintainers are allowed to perform regular maintenance. |
| + | |
| + | [https://wiki.pumpingstationone.org/Universal_Maintenance Universal Maintenance] |
| + | * [[Media:2_Table_Calibration_Platform_Lasers.pdf]] |
| + | * [[Media:5_Cleaning_and_Maintenance.pdf]] |
| | | |
| == List of Currently Authorized Users == | | == List of Currently Authorized Users == |
Line 144: |
Line 150: |
| ! Trained By | | ! Trained By |
| ! Date | | ! Date |
| + | |- |
| + | |[[user:mvictoras|Victor Mateevitsi]] |
| + | |Deanna Musurlian |
| + | |9/21/2019 |
| + | |- |
| + | |Nikolas Gamarra |
| + | |Deanna Musurlian |
| + | |9/21/2019 |
| |- | | |- |
| |Fritz Sullivan | | |Fritz Sullivan |
Line 222: |
Line 236: |
| |2018-08-2 | | |2018-08-2 |
| |- | | |- |
| + | |- |
| + | |[[Nathan Upchurch]] |
| + | |Deanna Williams |
| + | |2019-08-13 |
| + | |- |
| + | |} |
| + | |
| + | == List of Currently Authorized Maintainers == |
| + | |
| + | {| class="wikitable" border="1" |
| + | ! Qualified Member |
| + | ! Trained By |
| + | ! Date |
| + | |- |
| + | |[Maintainer] |
| + | |Trained by... |
| + | |Date trained... |
| | | |
| | | |