Line 51: |
Line 51: |
| | | |
| == Procedures == | | == Procedures == |
− |
| |
− | === Maintenance ===
| |
− | [https://wiki.pumpingstationone.org/Universal_Maintenance Universal Maintenance]
| |
− | * [[Media:2_Table_Calibration_Platform_Lasers.pdf]]
| |
− | * [[Media:5_Cleaning_and_Maintenance.pdf]]
| |
| | | |
| === Setting Up Your Computer=== | | === Setting Up Your Computer=== |
Line 74: |
Line 69: |
| === Exhaust === | | === Exhaust === |
| * Turn on the Exhaust Fan by flipping the switch on the gray box to the left of the Boss Laser. | | * Turn on the Exhaust Fan by flipping the switch on the gray box to the left of the Boss Laser. |
| + | * Make sure the BLAST GATE is open. |
| + | * It is always good practice to open the Make-up Air Window to allow fresh air to circulate while running a job. |
| | | |
| === Powering On Machine === | | === Powering On Machine === |
Line 79: |
Line 76: |
| | | |
| == Running your job == | | == Running your job == |
− | *Use the printer driver and Universal Control Panel (UCP) to send data to the laser. | + | * Use the printer driver and Universal Control Panel (UCP) to send data to the laser. |
− | *The printer driver is discussed from page 39-57 of the manual, and on page 58-62, the UCP is explained. | + | * The printer driver is discussed from page 39-57 of the manual, and on page 58-62, the UCP is explained. |
− | *https://wiki.pumpingstationone.org/images/Universal_PLS6.150D_user_guide.pdf | + | * https://wiki.pumpingstationone.org/images/Universal_PLS6.150D_user_guide.pdf |
| + | * ALLOW AT LEAST 30 SECONDS TO ELAPSE BEFORE LIFTING THE LID AFTER A JOB. |
| | | |
| === Powering Off Machine === | | === Powering Off Machine === |
− | * Allow the Exhaust & Air Assist to run for approximately 10-15 after completing a job. (DO NOT CYCLE THE EXHAUST SYSTEM RAPIDLY). | + | * Allow the Exhaust & Air Assist to run for approximately 10-15 min. after completing a job. (DO NOT CYCLE THE EXHAUST SYSTEM RAPIDLY). |
| * Turn off the Exhaust & Air Assist FIRST | | * Turn off the Exhaust & Air Assist FIRST |
| * Power down the machine | | * Power down the machine |
Line 137: |
Line 135: |
| |} | | |} |
| | | |
| + | |
| + | == Maintenance == |
| + | |
| + | Please note that ONLY authorized maintainers are allowed to perform regular maintenance. |
| + | |
| + | [https://wiki.pumpingstationone.org/Universal_Maintenance Universal Maintenance] |
| + | * [[Media:2_Table_Calibration_Platform_Lasers.pdf]] |
| + | * [[Media:5_Cleaning_and_Maintenance.pdf]] |
| | | |
| == List of Currently Authorized Users == | | == List of Currently Authorized Users == |
Line 144: |
Line 150: |
| ! Trained By | | ! Trained By |
| ! Date | | ! Date |
| + | |- |
| + | |[[user:mvictoras|Victor Mateevitsi]] |
| + | |Deanna Musurlian |
| + | |9/21/2019 |
| |- | | |- |
| |Nikolas Gamarra | | |Nikolas Gamarra |
Line 231: |
Line 241: |
| |2019-08-13 | | |2019-08-13 |
| |- | | |- |
| + | |} |
| + | |
| + | == List of Currently Authorized Maintainers == |
| + | |
| + | {| class="wikitable" border="1" |
| + | ! Qualified Member |
| + | ! Trained By |
| + | ! Date |
| + | |- |
| + | |[Maintainer] |
| + | |Trained by... |
| + | |Date trained... |
| + | |
| | | |
| [[Category:Laser Cutter]] | | [[Category:Laser Cutter]] |
| [[Category:Fabrication]] | | [[Category:Fabrication]] |
| [[Category:Certification Clarification Needed]] | | [[Category:Certification Clarification Needed]] |