Domain Admins
586
edits
Changes
From Pumping Station One
Created page with "{{Template:EquipmentPage |owner = PS:One |certification = yes |hackable = no |model = DoAll 16-2 |serial = |arrived = 9/19/14 |doesitwork = soon |contact = Dean Anderson |w..."
{{Template:EquipmentPage
|owner = PS:One
|certification = yes
|hackable = no
|model = DoAll 16-2
|serial =
|arrived = 9/19/14
|doesitwork = soon
|contact = Dean Anderson
|where =
|value = 900
}}
'''This tool requires certification for use.'''
== Specifications ==
{| class="wikitable" border="1"
|Capacity
|16" from the blade to the column
|-
|Blade Size
|120" blade. Width can be up to 1". Each blade width has a separate guide. We don't have guides larger than 1/2".
|-
|Blade Speed
|approximately 45 to 1600 FPM, continuously variable.
|-
|Power
|240V, 3 phase
|-
|Weight
|1500-2000 pounds
|-
|Mfg. Date
|1955
|-
|}
== Blades ==
Installed:
== To-Do ==
Install new blade.
Change oil in transmission.
Replace thrust bearings in blade guide.
== Maintenance ==
{| class="wikitable" border="1"
! Description
! Frequency
! Lubricant
! Instructions
! History
|-
|Hydraulic cylinder
|Maintain level at top of oil cup.
|
|
|
|-
|Gear Box
|yearly
|80W-90 gear oil
|Drain and fill with 3 ounces of oil.
Requires removing gearbox. See below.
|2/14 8 oz 85W90
|-
|Pivot bar
|monthly
|General purpose grease
|2 Zert fittings. Use grease gun.
|
|}
Gearbox oil change. Loosen 2 screws on the left edge of right top cover. Remove top 2 screws on the right side. Loosen bottom 2 screws on the right side cover. Slide top cover towards the center of the saw. Pivot the right cover down. Remove drive belt. Remove gearbox step pulley. Remove 3 bolts holding the gearbox. These are near the ring gear teeth. Remove the gearbox out the top of the saw between the two transverse brackets (long shaft comes out last). Drain/fill bolt is on the side opposite the pinion gear. Consider replacing the gaskets on the gearbox.
== Equipment ==
{| class="wikitable" border="1"
! Item
! Description
! Supplier
! Cost
|-
|
|Bimetal Bandsaw Blade, 137"L, 3/4"W
|
|
|}
== References ==
Manual for the latest version of the Model J (very similar).
http://www.dakecorp.com/manuals/Model%20Johnson%20J%20Saws.pdf
Good link for restoration, including coolant pan dimensions and bearing sizes. http://www.shopfloortalk.com/forums/showthread.php?t=21021
== List of Currently Certified Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
|-
|Dean Anderson
|
|-
|
|
|-
|
|
|-
|
|
|-
|}
[[Category:Metalworking]]
[[Category:Coldmetals]]
|owner = PS:One
|certification = yes
|hackable = no
|model = DoAll 16-2
|serial =
|arrived = 9/19/14
|doesitwork = soon
|contact = Dean Anderson
|where =
|value = 900
}}
'''This tool requires certification for use.'''
== Specifications ==
{| class="wikitable" border="1"
|Capacity
|16" from the blade to the column
|-
|Blade Size
|120" blade. Width can be up to 1". Each blade width has a separate guide. We don't have guides larger than 1/2".
|-
|Blade Speed
|approximately 45 to 1600 FPM, continuously variable.
|-
|Power
|240V, 3 phase
|-
|Weight
|1500-2000 pounds
|-
|Mfg. Date
|1955
|-
|}
== Blades ==
Installed:
== To-Do ==
Install new blade.
Change oil in transmission.
Replace thrust bearings in blade guide.
== Maintenance ==
{| class="wikitable" border="1"
! Description
! Frequency
! Lubricant
! Instructions
! History
|-
|Hydraulic cylinder
|Maintain level at top of oil cup.
|
|
|
|-
|Gear Box
|yearly
|80W-90 gear oil
|Drain and fill with 3 ounces of oil.
Requires removing gearbox. See below.
|2/14 8 oz 85W90
|-
|Pivot bar
|monthly
|General purpose grease
|2 Zert fittings. Use grease gun.
|
|}
Gearbox oil change. Loosen 2 screws on the left edge of right top cover. Remove top 2 screws on the right side. Loosen bottom 2 screws on the right side cover. Slide top cover towards the center of the saw. Pivot the right cover down. Remove drive belt. Remove gearbox step pulley. Remove 3 bolts holding the gearbox. These are near the ring gear teeth. Remove the gearbox out the top of the saw between the two transverse brackets (long shaft comes out last). Drain/fill bolt is on the side opposite the pinion gear. Consider replacing the gaskets on the gearbox.
== Equipment ==
{| class="wikitable" border="1"
! Item
! Description
! Supplier
! Cost
|-
|
|Bimetal Bandsaw Blade, 137"L, 3/4"W
|
|
|}
== References ==
Manual for the latest version of the Model J (very similar).
http://www.dakecorp.com/manuals/Model%20Johnson%20J%20Saws.pdf
Good link for restoration, including coolant pan dimensions and bearing sizes. http://www.shopfloortalk.com/forums/showthread.php?t=21021
== List of Currently Certified Users ==
{| class="wikitable" border="1"
! Qualified Member
! Trained By
|-
|Dean Anderson
|
|-
|
|
|-
|
|
|-
|
|
|-
|}
[[Category:Metalworking]]
[[Category:Coldmetals]]
